Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_all-in-one:p90u [2019/07/08 11:28] – [Installation] christianfaq:xpc_all-in-one:p90u [2019/07/09 09:58] (current) – [Introduction] SH
Line 1: Line 1:
-====== How can I install an LTE module in a P90U? =====+====== P90U ====== 
- +===== How can I install an LTE module in a P90U? ===== 
-===== Introduction ====+==== Introduction ==== 
- +<WRAP info 60%>
-<WRAP center round info 60%>+
 Shuttle does not offer an LTE kit for the P90U as standard. Such components are to be purchased by the customer.   Shuttle does not offer an LTE kit for the P90U as standard. Such components are to be purchased by the customer.  
 </WRAP> </WRAP>
- 
  
 In order to equip the Shuttle XPC all-in-one P90U (19.5") with an LTE mobile network function, the following components are required: In order to equip the Shuttle XPC all-in-one P90U (19.5") with an LTE mobile network function, the following components are required:
Line 14: Line 12:
     * HUAWEI MS2372h-517 (North/Latin America)     * HUAWEI MS2372h-517 (North/Latin America)
     * HUAWEI MS2372h-607 (Asia)     * HUAWEI MS2372h-607 (Asia)
 +
 +{{:faq:xpc_all-in-one:p90u:huawei_2.png?nolink&200|}} 
 +{{:faq:xpc_all-in-one:p90u:huawei_1.png?nolink&200|}}
  
 **Two external LTE antennas** **Two external LTE antennas**
-    * With SMA connector (male, with internal pin)+    * With SMA connector (male)
  
  **Two antenna cables**  **Two antenna cables**
     * Connector for the LTE module:  CRC9 (TS-5)     * Connector for the LTE module:  CRC9 (TS-5)
-    * Connector for the antenna: SMA (female, without internal pin+    * Connector for the antenna: SMA (female) 
     * Cable length for P90U: 14 and 38 cm     * Cable length for P90U: 14 and 38 cm
  
 +{{:faq:xpc_all-in-one:antenna.png?nolink&500|}}
  
- +==== Installation  ==== 
- +<WRAP important 60%>
-===== Installation  ====+
- +
-<WRAP center round info 60%>+
 Due to safety reasons, please turn off your computer completely first and unplug it from the power supply. Due to safety reasons, please turn off your computer completely first and unplug it from the power supply.
 </WRAP> </WRAP>
Line 34: Line 33:
 **Please install with reference to the following steps:** **Please install with reference to the following steps:**
  
- +  - Please remove the cover from the back of the P90U first, undo four screws of the stand mount and remove the stand. 
-1. Please remove the cover from the back of the P90U first, undo four screws of the stand mount and remove the stand. +  Unscrew four screws of the back cover and remove it.\\ {{:faq:xpc_all-in-one:p90u:open_chassis_p90_1.png?nolink&700|}} 
- +  Push the clip inward to unlock the eDP cable connector for removal. Unscrew ten screws of the middle cover and remove it. Remove the two antenna covers from both sides of the chassis (see pictures d, e).\\ {{:faq:xpc_all-in-one:p90u:open_chassis_p90_2.png?nolink&700|}} 
-2. Unscrew four screws of the back cover and remove it.  +  Take out the two antenna cable connectors and remove the locks.\\ {{:faq:xpc_all-in-one:p90u:antenna_cable.png?nolink&400|}} 
- +  First unscrew the two screws of the speaker to remove it (a). Lead the connector of the 380 mm antenna cable from the inside through the appropriate opening on the side of the chassis (b). Refasten the speaker with the two screws and route the antenna cable to the other side of chassis (c). Use the lock to affix the antenna from the outside (d).\\ {{:faq:xpc_all-in-one:p90u:antenna_cable_1.png?nolink&700|}}{{:faq:xpc_all-in-one:p90u:open_chassis_p90_3_middlecover.png?nolink&700|}} 
-{{ :faq:xpc_all-in-one:p90u:open_chassis_p90_1.png |}} +  Replace the middle cover and refasten the 10 screws. As shown, lead the connector of the 140 mm antenna cable from the inside through the appropriate opening on the side of the chassis and use the lock to affix the antenna from the outside.\\ {{:faq:xpc_all-in-one:p90u:open_chassis_p90_4.png?nolink&700|}} 
- +  Reconnect the eDP cable to "EDP1", then install the LTE module (optional) and connect the two antenna cable connectors to the LTE module (Main/Aux).\\ {{:faq:xpc_all-in-one:p90u:open_chassis_p90_5.png?nolink&700|}} 
- +  Replace the back cover. Refasten the stand and the back cover with eight screws. Replace the cover.\\ {{:faq:xpc_all-in-one:p90u:open_chassis_p90_6.png?nolink&700|}} 
-3. Push the clip inward to unlock the eDP cable connector for removal. Unscrew ten screws of the middle cover and remove it.Remove the two antenna covers from both sides of the chassis (see pictures d,e). +  - Screw the antennas into position as pictured. Make sure they are aligned vertically to achieve the best possible signal reception.\\ \\ <WRAP important 60%>Make sure the two antennas are aligned in the correct direction.</WRAP>\\ {{:faq:xpc_all-in-one:p90u:open_chassis_p90_7.png?nolink&700|}} 
- +  - Review the following BIOS setting to make sure that the LTE module is recognised correctly:\\ {{:faq:xpc_all-in-one:p90u:bios_setting.png?nolink&500|}} 
-{{ :faq:xpc_all-in-one:p90u:open_chassis_p90_2.png |}} +    * ''Advanced - Onboard Device Configuration - E-Key Device Select = USB''
- +
- +
-4. Take out the two antenna cable connectors and remove the locks. +
- +
-{{ :faq:xpc_all-in-one:p90u:antenna_cable.png |}} +
- +
-5. First unscrew the two screws of the speaker to remove it (a). Lead the connector of the 380 mm antenna cable from the inside through the appropriate opening on the side of the chassis (b). Refasten the speaker with the two screws and route the antenna cable to the other side of chassis (c). Use the lock to affix the antenna from the outside (d) +
- +
-{{ :faq:xpc_all-in-one:p90u:antenna_cable_1.png |}} +
- +
- +
-{{ :faq:xpc_all-in-one:p90u:open_chassis_p90_3_middlecover.png |}} +
- +
-6. Replace the middle cover and refasten the 10 screws. As shown, lead the connector of the 140 mm antenna cable from the inside through the appropriate opening on the side of the chassis and use the lock to affix the antenna from the outside. +
- +
-{{ :faq:xpc_all-in-one:p90u:open_chassis_p90_4.png |}} +
- +
-7. Reconnect the eDP cable to "EDP1", then install the LTE module (optional) and connect the two antenna cable connectors to the LTE module (Main/Aux). +
- +
-{{ :faq:xpc_all-in-one:p90u:open_chassis_p90_5.png |}} +
- +
- +
-8. Replace the back cover. Refasten the stand and the back cover with eight screws. Replace the cover. +
- +
- +
-{{ :faq:xpc_all-in-one:p90u:open_chassis_p90_6.png |}} +
- +
-- Screw the antennas into position as pictured. Make sure they are aligned vertically to achieve the best possible signal reception. +
- +
-<WRAP center round important 60%> +
-Make sure the two antennas are aligned in the correct direction. +
-</WRAP> +
- +
-{{ :faq:xpc_all-in-one:p90u:open_chassis_p90_7.png |}} +
- +
-9. Check the following BIOS setting to ensure that the LTE module will be recognized correctly: +
-{{ :faq:xpc_all-in-one:p90u:bios_setting.png |}} +
- +
-<wrap hi>Advanced - Onboard Device Configuration - E-Key Device Select = USB</wrap> +
- +
- +
- +
- +
- +
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2019/07/08 11:28
  • by christian