Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
faq:xpc_cube:sb61g2 [2016/08/26 14:20] Shuttlefaq:xpc_cube:sb61g2 [2017/01/27 14:49] – [Why won't the system boot after overclocking the CPU Clock?] christian
Line 1: Line 1:
 ====== SB61G2 ====== ====== SB61G2 ======
-===== How can I check my DDR is performing in dual channel mode? ===== +===== Why does the system fail to power up? ===== 
-  - Press the "Tab" key immediately when your screen displays the Intel logo at boot. \\ {{:faq:xpc_cube:sb61:sb61_dual_channel_01.jpg?nolink&100|}} +or //Why do the front audio ports fail to work?// or //Why do the front panel USB ports fail to work?// 
-  - Check the message from your monitor. \\ {{:faq:xpc_cube:sb61:sb61_dual_channel_02.jpg?nolink&400|}}+ 
 +At the front of the XPC SB61G2V3 is a flat cable connecting the daughterboard to the motherboard. If this cable is not connected properly, it will result in partial or full failure of the daughterboard. To correct this issue, please open the chassis and check the cable. 
 + 
 +  - Please double-check, if the "Flat cable" is properly connected to motherboard and the front audio board. Check that the cable is not concavely inserted into the header. \\ {{:faq:xpc_cube:sb61:sb61_flat_cable_01.jpg?nolink&400|}} 
 +  - Make sure the "Flat cable" is fastened by "Lock bar".  
 +  - Wind the "Flat cable" as follows to avoid future issues.  \\ {{:faq:xpc_cube:sb61:sb61_flat_cable_02.jpg?nolink&400|}} 
 + 
 +===== How can I check if my DDR memory is performing in dual channel mode? ===== 
 +  - Press the "Tab" key immediately when your screen displays the Intel logo during the boot process. \\ {{:faq:xpc_cube:sb61:sb61_dual_channel_01.jpg?nolink&100|}} 
 +  - Check the message which is now displayed. \\ {{:faq:xpc_cube:sb61:sb61_dual_channel_02.jpg?nolink&400|}}
  
 <WRAP center round tip 60%> <WRAP center round tip 60%>
-Note: Please refer to the user's manual page 38, you have to use the same size and type DIMMs on Channels 0 and 1.+Note: Please refer to the user's manual page 38. You need to use the same size and type of DIMMs on Channels 0 and 1.
 </WRAP> </WRAP>
  
 +===== Why won't the system boot after overclocking the CPU? =====
 +When overclocking the CPU's FSB frequency, the memory frequency will also overclock at the same time. When overclocking, make sure that you set the memory frequency to a lower level, so that when the FSB frequency is increased, memory frequency still is kept in a stable range. To do this, first unselect ''Auto'' of the ''Memory Frequency For'' as shown below. Try to set the memory frequency to a lower level (ex. DDR 266 / 333).
 +
 +{{:faq:xpc_cube:sb61:sb61_overclocking.png?nolink&500|}}
  
 ===== Why is there a delay on the S/PDIF-out signal?  ===== ===== Why is there a delay on the S/PDIF-out signal?  =====
  • Last modified: 2021/09/02 13:38
  • by TS