Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_cube:sb61g2 [2016/08/29 13:38]
Shuttle [Why won't the system boot after overclocking the CPU Clock?]
faq:xpc_cube:sb61g2 [2017/01/27 14:53] (current)
CS [Why is there a delay on the S/PDIF-out signal?]
Line 1: Line 1:
 ====== SB61G2 ====== ====== SB61G2 ======
 ===== Why does the system fail to power up? ===== ===== Why does the system fail to power up? =====
-or //Why do the front audio ports fail to work// or //Why do the front panel USB ports fail to work?//+or //Why do the front audio ports fail to work?// or //Why do the front panel USB ports fail to work?//
  
-At the front of the XPC SB61G2v3 ​is a flat cable connecting the daughter board to the motherboard. If this cable is not connected properly, it will result in partial ​of full failure of the daughterboard. To correct this issue, please open the chassis and check the cable.+At the front of the XPC SB61G2V3 ​is a flat cable connecting the daughterboard ​to the motherboard. If this cable is not connected properly, it will result in partial ​or full failure of the daughterboard. To correct this issue, please open the chassis and check the cable.
  
-  - Please double check the "Flat cable" is proper ​connected to motherboard and the front audio board. Check that the cable is not concavely inserted into the header. \\ {{:​faq:​xpc_cube:​sb61:​sb61_flat_cable_01.jpg?​nolink&​400|}}+  - Please double-check, if the "Flat cable" is properly ​connected to motherboard and the front audio board. Check that the cable is not concavely inserted into the header. \\ {{:​faq:​xpc_cube:​sb61:​sb61_flat_cable_01.jpg?​nolink&​400|}}
   - Make sure the "Flat cable" is fastened by "Lock bar"​. ​   - Make sure the "Flat cable" is fastened by "Lock bar"​. ​
-  - Wind the "Flat cable" as follows to avoid disturbing the cable in the future. ​ \\ {{:​faq:​xpc_cube:​sb61:​sb61_flat_cable_02.jpg?​nolink&​400|}}+  - Wind the "Flat cable" as follows to avoid future ​issues.  \\ {{:​faq:​xpc_cube:​sb61:​sb61_flat_cable_02.jpg?​nolink&​400|}}
  
-===== How can I check my DDR is performing in dual channel mode? ===== +===== How can I check if my DDR memory ​is performing in dual channel mode? ===== 
-  - Press the "​Tab"​ key immediately when your screen displays the Intel logo at boot. \\ {{:​faq:​xpc_cube:​sb61:​sb61_dual_channel_01.jpg?​nolink&​100|}} +  - Press the "​Tab"​ key immediately when your screen displays the Intel logo during the boot process. \\ {{:​faq:​xpc_cube:​sb61:​sb61_dual_channel_01.jpg?​nolink&​100|}} 
-  - Check the message ​from your monitor. \\ {{:​faq:​xpc_cube:​sb61:​sb61_dual_channel_02.jpg?​nolink&​400|}}+  - Check the message ​which is now displayed. \\ {{:​faq:​xpc_cube:​sb61:​sb61_dual_channel_02.jpg?​nolink&​400|}}
  
 <WRAP center round tip 60%> <WRAP center round tip 60%>
-Note: Please refer to the user's manual page 38, you have to use the same size and type DIMMs on Channels 0 and 1.+Note: Please refer to the user's manual page 38. You need to use the same size and type of DIMMs on Channels 0 and 1.
 </​WRAP>​ </​WRAP>​
  
-===== Why won't the system boot after overclocking the CPU Clock? ===== +===== Why won't the system boot after overclocking the CPU? ===== 
-When overclocking the CPU FSB Clock, the memory frequency will also overclock at the same time. When overclocking make sure that you set the memory frequency to lower level, ​such that increases in FSB keep the memory frequency in a stable range. To do this, first deselect ​''​Auto'' ​for the ''​Memory Frequency For''​ as shown below. Try to set memory frequency to a lower level (ex. DDR 266 / 333).+When overclocking the CPU'​s ​FSB frequency, the memory frequency will also overclock at the same time. When overclockingmake sure that you set the memory frequency to lower level, ​so that when the FSB frequency is increased, ​memory frequency ​still is kept in a stable range. To do this, first unselect ​''​Auto'' ​of the ''​Memory Frequency For''​ as shown below. Try to set the memory frequency to a lower level (ex. DDR 266 / 333).
  
 {{:​faq:​xpc_cube:​sb61:​sb61_overclocking.png?​nolink&​500|}} {{:​faq:​xpc_cube:​sb61:​sb61_overclocking.png?​nolink&​500|}}
  
-===== Why is there a delay on the S/PDIF-out signal? ​ ===== +===== Why is there a delay on the S/​PDIF ​output ​signal? ​ ===== 
-Issue: When a file is selected to play via SPDIF-out, it takes 0.5s before a sound begins ​playing. Thus the first 0.5s of a song is missed.+Issue: When a file is selected to be played ​via SPDIF, it takes 0.5 seconds for it to start playing. Thus the first 0.5 seconds ​of e.g. a song is missing.
  
-Fix: A beta driver has been developed ​to remove ​this issue. Please download the new audio driver file [[http://​download.shuttle.eu/​Archive_2004/​Drivers/​new/​fb61/​fb61v3/​cd560/​wdm_a357.zip|here]].+A beta driver has been released ​to fix this issue. Please download the new audio driver file from: [[http://​download.shuttle.eu/​Archive_2004/​Drivers/​new/​fb61/​fb61v3/​cd560/​wdm_a357.zip|here]].
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>​.}} {{backlinks>​.}}
  • faq/xpc_cube/sb61g2.1472477915.txt.gz
  • Last modified: 2016/08/29 13:38
  • by Shuttle