Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
faq:xpc_cube:sb77g5 [2016/08/26 12:35] – created Shuttlefaq:xpc_cube:sb77g5 [2017/07/17 11:25] Shuttle
Line 1: Line 1:
-====== Modellbezeichnung ====== +====== SB77G5====== 
-===== SG77G5 ===== +{{section>faq:xpc_cube:sg33g5#post_issue_on_shuttle_g5_models_-_check_setting_of_jumper_jp4&firstseconly&nofooter&noeditbutton&noreadmore}} 
-{{section>faq:xpc_cube:sg33g5#post_issuejp4_jumper_setting_for_shuttle_g5_models&firstseconly&nofooter&noeditbutton&noreadmore}}+===== Why does the SB77G5 sometimes hang upon reboot?  ===== 
 +This may be caused by an incorrect LAN firmware and chipset version. Please install the "Broadcom Advanced Control Suite" from your driver CD. You can check, if the versions match. 
 + 
 +{{:faq:xpc_cube:sb77:sb77_lan_firmware.jpg?nolink&400|}} 
 + 
 +If the ASIC Version is BCM5705 A3 and Firmware Version is 5788, please follow the procedures below: 
 + 
 +  - Prepare a boot disk, [[http://download.shuttle.eu/Archive_2010/Barebone/SB77G5/Driver/5705%20firmware%20update%20new.zip|download this patch]] and unzip the files on a disk. 
 +  - Shut down the SB77G5 and unplug the power cord for 30 seconds. 
 +  - Boot the system with this boot disk and enter 5705. 
 + 
 +<WRAP center round important 60%> 
 +Please note: This procedure only works if the ASIC version is **5705** and the Firmware version **5788**. 
 +</WRAP>  
 + 
 +===== How do I install RAID drivers on the SB77G5 during Windows 2000 or Windows XP installation? ===== 
 +In order to install Windows 2000 or Windows XP RAID drivers on the SB77G5, a floppy drive and floppy disk with the RAID driver is required. 
 + 
 +Before you start you will need to create an Intel RAID Driver Floppy Disk (create an Intel RAID Driver Floppy Disk or download the driver from here and extract/UnZip on a Floppy Disk directly): If you have the "Intel RAID Driver" disk from your XPC accessory box, skip this step. 
 + 
 +  - On a system running Windows, insert motherboard driver CD. 
 +  - Insert a blank floppy disk into the floppy drive. 
 +  - Doubleclick on the D:\Intel\Raid\F6 install\F6 install.exe and answer all prompts presented (assuming your CD-ROM drives letter is D.) 
 +  - When the installation is completed, your floppy disk should contain the following files: iaStor.cat, iaStor.inf, iaStor.cat, License.txt, readme.txt and TXTSETUP.oem. 
 +  - Go into the BIOS setup and enable Drive A and Onboard FDC Controller. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_01.jpg?nolink&400|}} 
 +  - Enable Drive A. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_02.jpg?nolink&400|}} 
 +  - Enable Onboard FDC Controller. 
 +  - Begin the Windows installation. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_03.jpg?nolink&400|}} 
 +  - Press the F6 key when the RAID setup message comes up. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_04.jpg?nolink&400|}} 
 +  - Press the S key to select the RAID driver. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_05.jpg?nolink&400|}} 
 +  - Insert the floppy disk you just made into the floppy disk drive. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_06.jpg?nolink&400|}} 
 +  - Select the relevant driver for your operating system. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_07.jpg?nolink&400|}} 
 +  - Once the driver is installed, press enter to continue the Windows installation.
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2021/09/02 13:38
  • by TS