Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
faq:xpc_cube:sb77g5 [2017/01/27 15:02] – [SG77G5] christian | faq:xpc_cube:sb77g5 [2017/01/31 16:54] – Shuttle | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | ====== |
{{section> | {{section> | ||
===== Why does the SB77G5 sometimes hang upon reboot? | ===== Why does the SB77G5 sometimes hang upon reboot? | ||
Line 6: | Line 6: | ||
{{: | {{: | ||
- | If the ASIC Version is BCM5705 A3 and Firmware Version is 5788. Please | + | If the ASIC Version is BCM5705 A3 and Firmware Version is 5788, please |
- | - Prepare a boot disk, [[http:// | + | - Prepare a boot disk, [[http:// |
- | - Shut down SB77G5 and unplug the power core for 30sec. | + | - Shut down the SB77G5 and unplug the power cord for 30 seconds. |
- | - Boot the system with this boot disk, and enter 5705. | + | - Boot the system with this boot disk and enter 5705. |
<WRAP center round important 60%> | <WRAP center round important 60%> | ||
- | Please note: this procedure only works when ASIC version is **5705** and Firmware version | + | Please note: This procedure only works if the ASIC version is **5705** and the Firmware version **5788**. |
</ | </ | ||
===== How do I install RAID drivers on the SB77G5 during Windows 2000 or Windows XP installation? | ===== How do I install RAID drivers on the SB77G5 during Windows 2000 or Windows XP installation? | ||
- | In order to install Windows 2000 or Windows XP RAID drivers on the SB77G5, a floppy drive and floppy disk with the RAID driver is needed. | + | In order to install Windows 2000 or Windows XP RAID drivers on the SB77G5, a floppy drive and floppy disk with the RAID driver is required. |
- | Before you start you will need to create | + | Before you start you will need to create |
- | - On a system running Windows, insert | + | - On a system running Windows, insert |
- | - Insert a blank floppy | + | - Insert a blank floppy |
- | - Double-click | + | - Doubleclick |
- | - When installation is complete, your floppy should contain the following files: iaStor.cat, iaStor.inf, iaStor.cat, License.txt, | + | - When the installation is completed, your floppy |
- | - Go into the BIOS setup utility | + | - Go into the BIOS setup and enable Drive A and Onboard FDC Controller. \\ {{: |
- Enable Drive A. \\ {{: | - Enable Drive A. \\ {{: | ||
- Enable Onboard FDC Controller. | - Enable Onboard FDC Controller. | ||
- | - Begin Windows installation \\ {{: | + | - Begin the Windows installation. \\ {{: |
- | - Press F6 function | + | - Press the F6 key when the RAID setup message |
- | - Press S key to select RAID driver. \\ {{: | + | - Press the S key to select |
- | - Insert the floppy disk you just made into the floppy drive. \\ {{: | + | - Insert the floppy disk you just made into the floppy |
- | - Select the driver for your operating system. \\ {{: | + | - Select the relevant |
- | - After the driver | + | - Once the driver |
==== Related links ==== | ==== Related links ==== | ||
{{backlinks> | {{backlinks> |