Differences

This shows you the differences between two versions of the page.

--- faq:xpc_cube:sb77g5 [2016/08/26 14:06] – Shuttle
+++ faq:xpc_cube:sb77g5 [2021/09/02 13:38] (current) – TS
@@ Line 1: / Line 1: @@
-====== SG77G5======
+====== SB77G5======
-{{section>faq:xpc_cube:sg33g5#post_issuejp4_jumper_setting_for_shuttle_g5_models&firstseconly&nofooter&noeditbutton&noreadmore}}
+{{section>faq:xpc_cube:sg33g5#post_issue_on_shuttle_g5_models_-_check_setting_of_jumper_jp4&firstseconly&nofooter&noeditbutton&noreadmore}}
-===== Why does SB77G5 sometimes hangs upon reboot?  =====
+{{section>faq:hardware:graphics#g-series&firstseconly&nofooter&noeditbutton&noreadmore}}
-This may be caused by incorrect LAN firmware and chipset version. Please install "Broadcom Advanced Control Suite" in your driver CD. You can check if the versions match.
+===== Why does the SB77G5 sometimes hang upon reboot?  =====
+This may be caused by an incorrect LAN firmware and chipset version. Please install the "Broadcom Advanced Control Suite" from your driver CD. You can check, if the versions match.
 {{:faq:xpc_cube:sb77:sb77_lan_firmware.jpg?nolink&400|}}
-If the ASIC Version is BCM5705 A3 and Firmware Version is 5788. Please follow the procedures below:
+If the ASIC Version is BCM5705 A3 and Firmware Version is 5788, please follow the procedures below:
-  - Prepare a boot disk, [[http://download.shuttle.eu/Archive_2010/Barebone/SB77G5/Driver/5705%20firmware%20update%20new.zip|download this patch]] and unzip the files onto the disk.
+  - Prepare a boot disk, [[https://download.shuttle.eu/Archive_2010/Barebone/SB77G5/Driver/5705%20firmware%20update%20new.zip|download this patch]] and unzip the files on a disk.
-  - Shut down SB77G5 and unplug the power core for 30sec.
+  - Shut down the SB77G5 and unplug the power cord for 30 seconds.
-  - Boot the system with this boot disk, and enter 5705.
+  - Boot the system with this boot disk and enter 5705.
 <WRAP center round important 60%>
-Please note: this procedure only works when ASIC version is **5705** and Firmware version is **5788**.
+Please note: This procedure only works if the ASIC version is **5705** and the Firmware version **5788**.
 </WRAP>
 ===== How do I install RAID drivers on the SB77G5 during Windows 2000 or Windows XP installation? =====
-In order to install Windows 2000 or Windows XP RAID drivers on the SB77G5, a floppy drive and floppy disk with the RAID driver is needed.
+In order to install Windows 2000 or Windows XP RAID drivers on the SB77G5, a floppy drive and floppy disk with the RAID driver is required.
-Before you start you will need to create a Intel RAID Driver Floppy Disk (create a Intel RAID Driver Floppy Disk or download the driver from here and extract/UnZip into a Floppy Disk directly): If you have the "Intel RAID Driver" disk from your XPC box, skip this step.
+Before you start you will need to create an Intel RAID Driver Floppy Disk (create an Intel RAID Driver Floppy Disk or download the driver from here and extract/UnZip on a Floppy Disk directly): If you have the "Intel RAID Driver" disk from your XPC accessory box, skip this step.
-  - On a system running Windows, insert Motherboard Driver CD.
+  - On a system running Windows, insert motherboard driver CD.
-  - Insert a blank floppy diskette into the floppy drive.
+  - Insert a blank floppy disk into the floppy drive.
-  - Double-click on the D:\Intel\Raid\F6 install\F6 install.exe and answer all prompts presented (Assumes your CD ROM Drives label is D.)
+  - Doubleclick on the D:\Intel\Raid\F6 install\F6 install.exe and answer all prompts presented (assuming your CD-ROM drives letter is D.)
-  - When installation is complete, your floppy should contain the following files: iaStor.cat, iaStor.inf, iaStor.cat, License.txt, readme.txt and TXTSETUP.oem.
+  - When the installation is completed, your floppy disk should contain the following files: iaStor.cat, iaStor.inf, iaStor.cat, License.txt, readme.txt and TXTSETUP.oem.
-  - Go into the BIOS setup utility and enable Drive A and Onboard FDC Controller. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_01.jpg?nolink&400|}}
+  - Go into the BIOS setup and enable Drive A and Onboard FDC Controller. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_01.jpg?nolink&400|}}
   - Enable Drive A. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_02.jpg?nolink&400|}}
   - Enable Onboard FDC Controller.
-  - Begin Windows installation \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_03.jpg?nolink&400|}}
+  - Begin the Windows installation. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_03.jpg?nolink&400|}}
-  - Press F6 function key when the Raid setup message string come up. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_04.jpg?nolink&400|}}
+  - Press the F6 key when the RAID setup message comes up. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_04.jpg?nolink&400|}}
-  - Press S key to select RAID driver. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_05.jpg?nolink&400|}}
+  - Press the S key to select the RAID driver. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_05.jpg?nolink&400|}}
-  - Insert the floppy disk you just made into the floppy drive. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_06.jpg?nolink&400|}}
+  - Insert the floppy disk you just made into the floppy disk drive. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_06.jpg?nolink&400|}}
-  - Select the driver for your operating system. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_07.jpg?nolink&400|}}
+  - Select the relevant driver for your operating system. \\ {{:faq:xpc_cube:sb77:sb77_raid_installation_07.jpg?nolink&400|}}
-  - After the driver has been installed, press Enter to continue installing Windows.
+  - Once the driver is installed, press enter to continue the Windows installation.
 ==== Related links ====
 {{backlinks>.}}