Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_cube:sd36g5 [2016/08/29 09:16] Shuttlefaq:xpc_cube:sd36g5 [2021/09/02 13:39] (current) TS
Line 1: Line 1:
 ====== SD36G5 ====== ====== SD36G5 ======
-{{section>faq:xpc_cube:sg33g5#post_issuejp4_jumper_setting_for_shuttle_g5_models&firstseconly&nofooter&noeditbutton&noreadmore}} +{{section>faq:xpc_cube:sg33g5#post_issue_on_shuttle_g5_models_-_check_setting_of_jumper_jp4&firstseconly&nofooter&noeditbutton&noreadmore}} 
- +{{section>faq:hardware:graphics#g-series&firstseconly&nofooter&noeditbutton&noreadmore}} 
-===== How to enable Viiv in SD36G5? ===== +===== How do I enable Viiv technology on my SD36G5? ===== 
-The Viiv Technology requirements list as following:+The Viiv Technology requirements are as follows:
   * Process: Pentium D processor   * Process: Pentium D processor
   * Chipset: Intel 945G + ICH7DH   * Chipset: Intel 945G + ICH7DH
   * LAN Chip: Intel PRO Client LAN   * LAN Chip: Intel PRO Client LAN
-  * Audio require: High Definition Audio +  * Audio: High Definition Audio 
-  * Hard drive: SATA interface and support NCQ function+  * Hard drive: SATA interface with NCQ support
   * Operating system: Microsoft Windows XP Media Center Edition Rollup 2.   * Operating system: Microsoft Windows XP Media Center Edition Rollup 2.
  
-If you have install external PCI-E graphic card, please install with MCE version of video driver+If you have PCI-E graphics card installed, please be sure to have the relevant video driver for the MCE version installed as well.
  
-First of all, please update the BIOS version to the latest version and Load Optimized Default after BIOS updated.+First of all, please update the BIOS version to the latest version and Load Optimized Default once the BIOS update is complete.
  
-  - Go into BIOS →''Integrated Peripherals''→''OnChip IDE Device'' change ''SATA Mode'' to ''AHCI''. \\ {{:faq:xpc_cube:sd36:sd36_viiv_01.jpg?nolink&400|}} +  - Enter BIOS, and go to →''Integrated Peripherals''→''OnChip IDE Device''. Here, change ''SATA Mode'' to ''AHCI''. \\ {{:faq:xpc_cube:sd36:sd36_viiv_01.jpg?nolink&400|}} 
-  - Enable ''Quick Resume Technology'' from Power Management Setup. \\ {{:faq:xpc_cube:sd36:sd36_viiv_02.jpg?nolink&400|}} +  - Enable ''Quick Resume Technology'' in the Power Management Setup. \\ {{:faq:xpc_cube:sd36:sd36_viiv_02.jpg?nolink&400|}} 
-  - Before you have start to install MCE, you will need to papre a floppy drive and the 32bit ICH7R RAID disk that come with accessory box. If you do not have this floppy diskette, you may also download it from our website or driver CD. ''D:\Intel\F6 install\F6flpy32.exe'' and answer all prompts presented (Assumes your CD ROM Drives label is D.) +  - Before you begin installing MCE, you need a floppy disk drive and to prepare a floppy disk with the 32-bit ICH7R RAID disk driver that comes with the accessory box. You may otherwise download it from our website or take it from the driver CD. Proceed with ''D:\Intel\F6 install\F6flpy32.exe'' and answer all prompts presented (Assuming your CD-ROM drives label is D.) 
-  - Begin Windows MCE installation \\ {{:faq:xpc_cube:sd36:sd36_viiv_03.jpg?nolink&400|}} +  - Now begin to install Windows MCE\\ {{:faq:xpc_cube:sd36:sd36_viiv_03.jpg?nolink&400|}} 
-  - Press ''F6'' function key when the RAID setup message screen come up. \\ {{:faq:xpc_cube:sd36:sd36_viiv_04.jpg?nolink&400|}} +  - Press the ''F6'' function key when the RAID setup message screen comes up. \\ {{:faq:xpc_cube:sd36:sd36_viiv_04.jpg?nolink&400|}} 
-  - Press ''S'' key to select AHCI driver \\ {{:faq:xpc_cube:sd36:sd36_viiv_05.jpg?nolink&400|}} +  - Press the ''S'' key to select the AHCI driver\\ {{:faq:xpc_cube:sd36:sd36_viiv_05.jpg?nolink&400|}} 
-  - Insert the floppy disk you just made into the floppy drive. \\ {{:faq:xpc_cube:sd36:sd36_viiv_06.jpg?nolink&400|}} +  - Insert the floppy disk you prepared with the driver into the floppy drive. \\ {{:faq:xpc_cube:sd36:sd36_viiv_06.jpg?nolink&400|}} 
-  - Select the driver for chipset type "82801GR/GH SATA AHCI Controller (Desktop ICH7R/DH)" \\ {{:faq:xpc_cube:sd36:sd36_viiv_07.jpg?nolink&400|}} +  - Select the driver of the relevant chipset type"82801GR/GH SATA AHCI Controller (Desktop ICH7R/DH)" \\ {{:faq:xpc_cube:sd36:sd36_viiv_07.jpg?nolink&400|}} 
-  - After the driver has been selected, press Enter to continue installing Windows MCE. +  - When the driver is selected, press Enter to continue the Windows MCE installation
-  - Installing All the drivers from CD driver include Quick Resume driver under Windows MCE. \\ {{:faq:xpc_cube:sd36:sd36_viiv_08.jpg?nolink&400|}} {{:faq:xpc_cube:sd36:sd36_viiv_09.jpg?nolink&400|}} +  - Now please install all the drivers from the driver CD, which also include the Quick Resume driver, for Windows MCE. \\ {{:faq:xpc_cube:sd36:sd36_viiv_08.jpg?nolink&400|}} {{:faq:xpc_cube:sd36:sd36_viiv_09.jpg?nolink&400|}} 
-  - Installing Viiv driver \\ {{:faq:xpc_cube:sd36:sd36_viiv_10.jpg?nolink&400|}} {{:faq:xpc_cube:sd36:sd36_viiv_11.jpg?nolink&400|}} +  - Please install the Viiv driver\\ {{:faq:xpc_cube:sd36:sd36_viiv_10.jpg?nolink&400|}} {{:faq:xpc_cube:sd36:sd36_viiv_11.jpg?nolink&400|}} 
-  - After all the drivers installed, please restart the system. +  - When all the drivers are installed, please restart the system.
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2016/08/29 09:16
  • by Shuttle