Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
faq:xpc_cube:sd37p2 [2017/02/01 10:43] – [How do I get the best out of my memory in Dual Channel mode and what aspects should I pay attention to?] christianfaq:xpc_cube:sd37p2 [2017/02/01 10:51] – [Why is my DDR2-800 memory only displayed as DDR2-667 on the POST screen?] christian
Line 24: Line 24:
   - Should the message "Dual Channel Mode Enabled" not be displayed while booting, the memory is running in Single Channel mode only. \\ {{:faq:xpc_cube:sd37:sd37_dual_channel_03.jpg?nolink&400|}}   - Should the message "Dual Channel Mode Enabled" not be displayed while booting, the memory is running in Single Channel mode only. \\ {{:faq:xpc_cube:sd37:sd37_dual_channel_03.jpg?nolink&400|}}
  
-===== Why my DDRII 800 only show DDRII 667 at POST screen? ===== +===== Why is my DDR2-800 memory only displayed as DDR2-667 on the POST screen? ===== 
-According to Intel'SPEC for chipset 975X, it can only support up to 2 DDRII 800. If your memory modules show DDR667, you will adjust the frequency speed by manually in the BIOS. You may follow below instruction for setup.+According to Intel'specifications of the 975X chipset, it supports a total of two DDR2-800 modules. If your memory modules are shown as DDR2-667, you will need to set the frequency speed manually in the BIOS. Please follow the below steps.
  
-  - Boot Into BIOSand select the Frequency/Voltage Control \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_01.jpg?nolink&400|}}+  - Enter BIOS and select the Frequency/Voltage Control \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_01.jpg?nolink&400|}}
   - DRAM Timing Selectable selects the Manual \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_02.jpg?nolink&400|}}   - DRAM Timing Selectable selects the Manual \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_02.jpg?nolink&400|}}
   - System Memory Frequency select to 800MHz \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_03.jpg?nolink&400|}}   - System Memory Frequency select to 800MHz \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_03.jpg?nolink&400|}}
-  - Press F10 key save to CMOS and EXIT \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_04.jpg?nolink&400|}} +  - Press the F10 key to save to CMOS and exit BIOS. \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_04.jpg?nolink&400|}} 
-  - Check the post screen is DDRII 800 \\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_05.jpg?nolink&400|}}+  - Check the post screen whether it shows DDR2-800\\ {{:faq:xpc_cube:sd37:sd37_ddr2_800_05.jpg?nolink&400|}}
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2021/08/09 12:32
  • by Shuttle