Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_cube:sd37p2 [2016/08/29 09:21]
Shuttle
faq:xpc_cube:sd37p2 [2017/02/01 10:54] (current)
CS [Why is my DDR2-800 memory only displayed as DDR2-667 on the POST screen?]
Line 1: Line 1:
 ====== SD37P2 ====== ====== SD37P2 ======
-===== Why my SD37P2 ​run unstable after I installed Adobe Premiere Elements? ===== +===== How do I identify the version of my SD37P2? ===== 
-Because Adobe Premiere Elements have compatibility issue with Realtek audio driver. The new Realtek driver can solve this issue. Adobe has suggest ​the user has using Premiere Elements to go Realtek ​and download the audio driver Version R1.35 ([[http://​download.shuttle.eu/​Archive_2004/​Drivers/​new/​sd37p2/​old%20audio/​audio.zip|Download]]) to solve this problem. For more informationwe will suggest you to [[http://​www.adobe.com/​support/​techdocs/​332888.html|visit Adobe]] for more detail instruction+There are two versions of the SD37P2, V1 and V2If you are not sure which version you purchasedplease proceed as below to identify the version.
  
-===== How to get the best use of SD37P2 ​in Dual Channel mode and what aspects should be pay attention to===== +^If the PCS is 1.X or the BIOS ID's 6th digit is 0, please download the BIOS SD37V1.x at: [[http://​download.shuttle.eu/​Mirror/​XPC/​SD37P2/​|link]]^^ 
-The Dual Channel function of SD37P2To enable your SD37P2 memory DDR2 with Dual Channel, please ​refer to the steps below.+|{{:​faq:​xpc_cube:​sd37:​sd37_identification_01.jpg?nolink&​300|}}|{{:​faq:​xpc_cube:​sd37:​sd37_identification_02.jpg?​nolink&​300|}}| 
 +^If the PCB is 2.X or the BIOS ID's 6th digit is 2, please ​download ​the BIOS SD37V2.X at: [[http://​download.shuttle.eu/​Mirror/​XPC/​SD37P2_V2/​Bios/​|link]]^^ 
 +|{{:​faq:​xpc_cube:​sd37:​sd37_identification_03.jpg?​nolink&​300|}}|{{:​faq:​xpc_cube:​sd37:​sd37_identification_04.jpg?​nolink&​300|}}|
  
-  ​Please make sure to put the same memory DDR2 in the same color slot. (If putting memories into the different color slots, XPC will run in a Single Channel Mode.) \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_01.jpg?​nolink&​400|}} +===== Why won't my SD37P2 support some of ATI's video cards? ===== 
-  ​If the memories have been set up successfully,​ the function of Dual Channel ​will be detected and will also show the message ​on the screen while XPC is startingThus the function of Dual Channel would be normally operated. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_02.jpg?​nolink&​400|}} +The SD37P2 has two PCI-slots. ​The PCI-E 16x bandwidth ​will be halved to 8x speed on each slot. If your video card only supports 16x speed, it will not run on this systemPlease check your video card specifications or contact your video card vendor for detailed information.
-  - If memories DDR2 set on the different color memory slots, it doesn'​t show "Dual Channel Mode enables" ​on the screenAnd it will be a Single Channel Mode only\\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_03.jpg?​nolink&​400|}}+
  
-===== Why my DDRII 800 only show DDRII 667 at POST screen? ===== +===== Does my SD37P2 support four DIMMs of DDR2-667 memory? ===== 
-According to Intel'​s SPEC for chipset 975X, it can only support up to 2 DDRII 800If your memory modules show DDR667you will adjust ​the frequency speed by manually in the BIOS. You may follow below instruction for setup.+Yes, it doesShould it however turn out that it won't run stablethe system ​will automatically clock down the memory to 533 MHz to stabilise.
  
-  - Boot Into BIOS, and select ​the Frequency/​Voltage Control \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_01.jpg?​nolink&​400|}} +===== Why does my SD37P2 run unstable when I install Adobe Premiere Elements? ===== 
-  - DRAM Timing Selectable ​selects the Manual \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_02.jpg?​nolink&​400|}} +This is because Adobe Premiere Elements has compatibility issues with the Realtek audio driver. A new Realtek driver will help. Please update to version R1.35 ([[http://​download.shuttle.eu/​Archive_2004/​Drivers/​new/​sd37p2/​old%20audio/​audio.zip|Download]]). For more informationplease also [[http://​www.adobe.com/​support/​techdocs/​332888.html|visit Adobe]].  
-  - System Memory Frequency ​select ​to 800MHz ​\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_03.jpg?​nolink&​400|}} + 
-  - Press F10 key save to CMOS and EXIT \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_04.jpg?​nolink&​400|}} +===== How do I get the best out of my memory in Dual Channel mode and what aspects should I pay attention to? ===== 
-  - Check the post screen ​is DDRII 800 \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_05.jpg?​nolink&​400|}}+To enable your SD37P2 DDR2 memory in Dual Channel mode, please refer to the steps below. 
 + 
 +  - Please make sure to put the very same DDR2 memory (type and brand) in the slot of the same colour. (If modules are installed in slots of different colour, they will run in Single Channel mode.) \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_01.jpg?​nolink&​400|}} 
 +  - If the modules are installed correctly, Dual Channel will be shown on a screen when booting the XPC. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_02.jpg?​nolink&​400|}} 
 +  - Should the message "Dual Channel Mode Enabled"​ not be displayed while booting, the memory is running in Single Channel mode only. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_03.jpg?​nolink&​400|}} 
 + 
 +===== Why is my DDR2-800 memory only displayed as DDR2-667 on the POST screen? ===== 
 +According to Intel'​s specifications of the 975X chipset, it supports a total of two DDR2-800 modules. If your memory modules are shown as DDR2-667, you will need to set the frequency speed manually in the BIOS. Please follow the below steps. 
 + 
 +  - Enter BIOS and go to Frequency/​Voltage Control\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_01.jpg?​nolink&​400|}} 
 +  - Under DRAM Timing Selectable ​select "Manual"​. ​\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_02.jpg?​nolink&​400|}} 
 +  - Set System Memory Frequency to 800 MHz. \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_03.jpg?​nolink&​400|}} 
 +  - Press the F10 key to save changes ​to CMOS and exit BIOS. \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_04.jpg?​nolink&​400|}} 
 +  - Check the post screen ​whether it shows DDR2-800\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_05.jpg?​nolink&​400|}}
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>​.}} {{backlinks>​.}}
  • Last modified: 2016/08/29 09:21
  • by Shuttle