Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_cube:sd37p2 [2017/02/01 10:13]
CS [Why my SD37P2 run unstable after I installed Adobe Premiere Elements?]
faq:xpc_cube:sd37p2 [2017/02/01 10:54] (current)
CS [Why is my DDR2-800 memory only displayed as DDR2-667 on the POST screen?]
Line 17: Line 17:
 This is because Adobe Premiere Elements has compatibility issues with the Realtek audio driver. A new Realtek driver will help. Please update to version R1.35 ([[http://​download.shuttle.eu/​Archive_2004/​Drivers/​new/​sd37p2/​old%20audio/​audio.zip|Download]]). For more information,​ please also [[http://​www.adobe.com/​support/​techdocs/​332888.html|visit Adobe]]. ​ This is because Adobe Premiere Elements has compatibility issues with the Realtek audio driver. A new Realtek driver will help. Please update to version R1.35 ([[http://​download.shuttle.eu/​Archive_2004/​Drivers/​new/​sd37p2/​old%20audio/​audio.zip|Download]]). For more information,​ please also [[http://​www.adobe.com/​support/​techdocs/​332888.html|visit Adobe]]. ​
  
-===== How to get the best use of SD37P2 ​in Dual Channel mode and what aspects should ​be pay attention to? ===== +===== How do I get the best out of my memory ​in Dual Channel mode and what aspects should ​pay attention to? ===== 
-To enable your SD37P2 ​memory ​DDR2 with Dual Channel, please refer to the steps below.+To enable your SD37P2 DDR2 memory in Dual Channel ​mode, please refer to the steps below.
  
-  - Please make sure to put the same memory ​DDR2 in the same color slot. (If putting memories into the different ​color slotsXPC will run in Single Channel ​Mode.) \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_01.jpg?​nolink&​400|}} +  - Please make sure to put the very same DDR2 memory (type and brand) ​in the slot of the same colour. (If modules are installed in slots of different ​colourthey will run in Single Channel ​mode.) \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_01.jpg?​nolink&​400|}} 
-  - If the memories have been set up successfullythe function of Dual Channel will be detected and will also show the message ​on the screen while XPC is starting. Thus the function of Dual Channel would be normally operated. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_02.jpg?​nolink&​400|}} +  - If the modules are installed correctly, Dual Channel will be shown on a screen when booting ​the XPC. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_02.jpg?​nolink&​400|}} 
-  - If memories DDR2 set on the different color memory slots, it doesn'​t show "Dual Channel Mode enables" ​on the screen. And it will be a Single Channel ​Mode only. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_03.jpg?​nolink&​400|}}+  - Should ​the message ​"Dual Channel Mode Enabled" ​not be displayed while booting, ​the memory is running in Single Channel ​mode only. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_03.jpg?​nolink&​400|}}
  
-===== Why my DDRII 800 only show DDRII 667 at POST screen? ===== +===== Why is my DDR2-800 memory ​only displayed as DDR2-667 on the POST screen? ===== 
-According to Intel'​s ​SPEC for chipset ​975X, it can only support up to 2 DDRII 800. If your memory modules ​show DDR667, you will adjust ​the frequency speed by manually in the BIOS. You may follow below instruction for setup.+According to Intel'​s ​specifications of the 975X chipset, it supports a total of two DDR2-800 modules. If your memory modules ​are shown as DDR2-667, you will need to set the frequency speed manually in the BIOS. Please ​follow ​the below steps.
  
-  - Boot Into BIOSand select the Frequency/​Voltage Control \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_01.jpg?​nolink&​400|}} +  - Enter BIOS and go to Frequency/​Voltage Control\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_01.jpg?​nolink&​400|}} 
-  - DRAM Timing Selectable ​selects the Manual \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_02.jpg?​nolink&​400|}} +  - Under DRAM Timing Selectable ​select "Manual"​. ​\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_02.jpg?​nolink&​400|}} 
-  - System Memory Frequency ​select ​to 800MHz ​\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_03.jpg?​nolink&​400|}} +  - Set System Memory Frequency to 800 MHz. \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_03.jpg?​nolink&​400|}} 
-  - Press F10 key save to CMOS and EXIT \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_04.jpg?​nolink&​400|}} +  - Press the F10 key to save changes ​to CMOS and exit BIOS. \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_04.jpg?​nolink&​400|}} 
-  - Check the post screen ​is DDRII 800 \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_05.jpg?​nolink&​400|}}+  - Check the post screen ​whether it shows DDR2-800\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_05.jpg?​nolink&​400|}}
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>​.}} {{backlinks>​.}}
  • Last modified: 2017/02/01 10:13
  • by CS