Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_cube:sd37p2 [2017/02/01 10:43]
CS [How do I get the best out of my memory in Dual Channel mode and what aspects should I pay attention to?]
faq:xpc_cube:sd37p2 [2017/02/01 10:54] (current)
CS [Why is my DDR2-800 memory only displayed as DDR2-667 on the POST screen?]
Line 24: Line 24:
   - Should the message "Dual Channel Mode Enabled"​ not be displayed while booting, the memory is running in Single Channel mode only. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_03.jpg?​nolink&​400|}}   - Should the message "Dual Channel Mode Enabled"​ not be displayed while booting, the memory is running in Single Channel mode only. \\ {{:​faq:​xpc_cube:​sd37:​sd37_dual_channel_03.jpg?​nolink&​400|}}
  
-===== Why my DDRII 800 only show DDRII 667 at POST screen? ===== +===== Why is my DDR2-800 memory ​only displayed as DDR2-667 on the POST screen? ===== 
-According to Intel'​s ​SPEC for chipset ​975X, it can only support up to 2 DDRII 800. If your memory modules ​show DDR667, you will adjust ​the frequency speed by manually in the BIOS. You may follow below instruction for setup.+According to Intel'​s ​specifications of the 975X chipset, it supports a total of two DDR2-800 modules. If your memory modules ​are shown as DDR2-667, you will need to set the frequency speed manually in the BIOS. Please ​follow ​the below steps.
  
-  - Boot Into BIOSand select the Frequency/​Voltage Control \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_01.jpg?​nolink&​400|}} +  - Enter BIOS and go to Frequency/​Voltage Control\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_01.jpg?​nolink&​400|}} 
-  - DRAM Timing Selectable ​selects the Manual \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_02.jpg?​nolink&​400|}} +  - Under DRAM Timing Selectable ​select "Manual"​. ​\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_02.jpg?​nolink&​400|}} 
-  - System Memory Frequency ​select ​to 800MHz ​\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_03.jpg?​nolink&​400|}} +  - Set System Memory Frequency to 800 MHz. \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_03.jpg?​nolink&​400|}} 
-  - Press F10 key save to CMOS and EXIT \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_04.jpg?​nolink&​400|}} +  - Press the F10 key to save changes ​to CMOS and exit BIOS. \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_04.jpg?​nolink&​400|}} 
-  - Check the post screen ​is DDRII 800 \\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_05.jpg?​nolink&​400|}}+  - Check the post screen ​whether it shows DDR2-800\\ {{:​faq:​xpc_cube:​sd37:​sd37_ddr2_800_05.jpg?​nolink&​400|}}
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>​.}} {{backlinks>​.}}
  • Last modified: 2017/02/01 10:43
  • by CS