Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		 Previous revision
faq:xpc_cube:sh310r4 [2019/07/09 10:05] – created TSfaq:xpc_cube:sh310r4 [2023/03/21 16:10] (current) – TS
Line 1: Line 1:
 ====== SH310R4 ====== ====== SH310R4 ======
 +{{section>faq:hardware:cpu#does_my_shuttle_product_support_9th_gen_coffee_lake_refresh_processors&firstseconly&nofooter&noeditbutton&noreadmore}}
 +{{section>faq:hardware:graphics#j-series_r-series_r4_r6&firstseconly&nofooter&noeditbutton&noreadmore}}
 +{{section>faq:xpc_cube:sh310r4#how_to_print_your_very_own_custom_front_panel&firstseconly&nofooter&noeditbutton&noreadmore}}
 +===== How to print your very own custom front panel =====
 +The R4 (and similar) front panel comes with a removable acrylic plate which allows for creating individual front designs. Simply change the mylar and add your design such as a photo, graphics or a company logo to the front panel in just a few steps.
 +
 +With {{:faq:xpc_cube:sh310:j1_j4_r4_front.pdf|this empty PDF template}} in A4 format, you can design and print a perfectly fitting front panel of the J1, J4 und R4 chassis every major graphic design software.
 +
 +{{:faq:xpc_cube:sh310:j1_j4_r4_front_panel.png?nolink&400|}}
 +
 +In case you want to create a design from scratch, use these information:
 +
 +{{:faq:xpc_cube:sh310:r4_front_panel_dimensions.png?nolink&700|}}\\ All dimensions in millimetres (mm)
 ===== Quick Installation Guide ===== ===== Quick Installation Guide =====
 ==== Begin Installation ==== ==== Begin Installation ====
Line 5: Line 18:
 Due to safety reasons, please ensure that the power cord is disconnected before opening the case. Due to safety reasons, please ensure that the power cord is disconnected before opening the case.
 </WRAP> </WRAP>
-  - Unscrew 3 thumbscrews of the chassis cover. +  - Unscrew three thumbscrews of the chassis cover. 
-  - Slide the cover backwards and upwards.\\ {{:faq:xpc_cube:sh310:installation01.png?nolink&400|}}+  - Slide the cover backward and upward.\\ {{:faq:xpc_cube:sh310:installation01.png?nolink&400|}}
   - Unfasten the rack mount screws and remove the rack.\\ {{:faq:xpc_cube:sh310:installation02.png?nolink&400|}}   - Unfasten the rack mount screws and remove the rack.\\ {{:faq:xpc_cube:sh310:installation02.png?nolink&400|}}
 ==== CPU and Heatpipe Installation ==== ==== CPU and Heatpipe Installation ====
-  - Unfasten the Heatpipe fan thumbscrews on the back of the chassis. +  - Unfasten the thumbscrews of the heatpipe fan at the back of the chassis. 
-  - Unfasten the four Heatpipe module attachment screws and unplug the fan connector.\\ {{:faq:xpc_cube:sh310:installation03.png?nolink&500|}} +  - Unfasten the four heatpipe module attachment screws and unplug the fan connector.\\ {{:faq:xpc_cube:sh310:installation03.png?nolink&500|}} 
-  - Remove the Heatpipe module from the chassis and put it aside.\\ \\ <WRAP important 60%>This 1151-pin socket is easily damaged and pins bend quickly. Always use extreme care when installing a CPU and limit the number of times that you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage of the CPU.</WRAP>\\ → Follow the steps below to correctly install the CPU into the motherboard CPU socket.+  - Remove the heatpipe module from the chassis and put it aside.\\ \\ <WRAP important 60%>This 1151-pin socket is easily damaged and pins bend quickly. Always use extreme care when installing a CPU and limit the number of times you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage of the CPU.</WRAP>\\ → Follow the steps below to correctly install the CPU into the motherboard CPU socket.
   - First unlock and raise the socket lever.\\ {{:faq:xpc_cube:sh310:installation04.png?nolink&500|}}   - First unlock and raise the socket lever.\\ {{:faq:xpc_cube:sh310:installation04.png?nolink&500|}}
-  - Tear off the protective membrane from the metal load plate. Lift the metal load plate off the CPU socket.\\ {{:faq:xpc_cube:sh310:installation05.png?nolink&500|}}\\ \\ <WRAP important 60%>DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed. </WRAP> +  - Tear off the protective membrane from the metal load plate. Lift the metal load plate off the CPU socket.\\ {{:faq:xpc_cube:sh310:installation05.png?nolink&500|}}\\ \\ <WRAP important 60%>DO NOT touch the socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed. </WRAP> 
-  - Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket.\\ {{:faq:xpc_cube:sh310:installation06.png?nolink&500|}}\\ \\ <WRAP important 60%>Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins and damage of CPU!</WRAP>+  - Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket.\\ {{:faq:xpc_cube:sh310:installation06.png?nolink&500|}}\\ \\ <WRAP important 60%>Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins and damage of the CPU!</WRAP>
   - Close the metal load plate, lower the CPU socket lever and lock in place.   - Close the metal load plate, lower the CPU socket lever and lock in place.
   - Spread thermal paste evenly on the CPU surface.\\ {{:faq:xpc_cube:sh310:installation07.png?nolink&500|}}   - Spread thermal paste evenly on the CPU surface.\\ {{:faq:xpc_cube:sh310:installation07.png?nolink&500|}}
-  - Screw the Heatpipe module to the mainboard. Note to press down on the opposite diagonal corner while tightening each screw.+  - Screw the heatpipe module on to the mainboard. Note to press down on the opposite diagonal corner while tightening each screw.
   - Connect the fan connector.\\ {{:faq:xpc_cube:sh310:installation08.png?nolink&500|}}   - Connect the fan connector.\\ {{:faq:xpc_cube:sh310:installation08.png?nolink&500|}}
-  - Fasten the Smart Fan to the chassis with the four thumbscrews.\\ {{:faq:xpc_cube:sh310:installation09.png?nolink&500|}}+  - Re-fasten the Smart Fan using the four thumbscrews.\\ {{:faq:xpc_cube:sh310:installation09.png?nolink&500|}}
 ==== Memory Module Installation ==== ==== Memory Module Installation ====
 **Guidelines for Memory Configuration**\\ Before installing DIMMs, read and follow these guidelines for memory configuration:\\ \\ <WRAP important 60%>Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips are used. (Go to Shuttle’s website for the latest memory support list.) Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch direction.</WRAP> **Guidelines for Memory Configuration**\\ Before installing DIMMs, read and follow these guidelines for memory configuration:\\ \\ <WRAP important 60%>Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips are used. (Go to Shuttle’s website for the latest memory support list.) Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch direction.</WRAP>
Line 51: Line 64:
   - Complete.\\ \\ <WRAP tip 60%>Please press the ''Del'' key while booting to enter BIOS. Here, please load the optimised BIOS settings.</WRAP>   - Complete.\\ \\ <WRAP tip 60%>Please press the ''Del'' key while booting to enter BIOS. Here, please load the optimised BIOS settings.</WRAP>
  
 +===== Jumper settings and pinout =====
 +==== Front audio header (JP1) ====
 +<code>
 +1=MIC_L
 +2=AGND
 +3=MIC_R
 +4=Front_Detect
 +5=HP_R
 +6=Mic_detect
 +7=Sense_B
 +8=NULL
 +9=HP_L
 +10=HP_Detect
 +</code>
 +<a2s>
 +        JP1
 +     .---.---.
 +   1 | ■ | ● | 2
 +     .---.---.
 +   3 | ● | ● | 4
 +     .---.---.
 +   5 | ● | ● | 6
 +     .---.---.
 +   7 | ● |   | 8
 +     .---.---.
 +   9 | ● | ● | 10
 +     .---.---.
 +</a2s>
 +
 +==== Fan connectors (FAN1, FAN2) ====
 +<code>
 +1=GND
 +2=+12V
 +3=SPEED_SENSE
 +4=PWM_CTRL
 +</code>
 +<a2s>
 +     FAN1           FAN2
 +                  #------# 
 + #---------#      |   ■  | 4
 + |   ----- |      |   ■ || 3
 + | ■ ■ ■ ■ |      |   ■ || 2
 + | 4 3 2 1 |      |   ■ || 1
 + #---------#      #------#
 +</a2s>
 +
 +==== COM header (COM1) ====
 +<code>
 +1=DCD
 +2=RXD
 +3=TXD
 +4=DTR
 +5=GND
 +6=DSR
 +7=RTS
 +8=CTS
 +9=-XRI1
 +10=NULL
 +</code>
 +<a2s>
 +    2   4   6   8   10
 +  .---.---.---.---.---.
 +  | ● | ● | ● | ● |   |
 +  .---.---.---.---.---.
 +  | ■ | ● | ● | ● | ● |
 +  .---.---.---.---.---.
 +    1   3   5   7   9
 +</a2s>
 +
 +==== LPC header (LPC1) ====
 +<code>
 +1=+12V
 +2=VCC
 +3=5V_DUAL
 +4=SERIRQ
 +5=LPC24M_1
 +6=LPC24M_2
 +7=SIORST-
 +8=LFRAME
 +9=LAD3
 +10=LAD2
 +11=-12V
 +12=3VSB
 +13=NA
 +14=LDRQ0-
 +15=PCH_PME-
 +16=LAD1
 +17=LAD0
 +18=VCC3
 +19=GND
 +20=NULL
 +</code>
 +<a2s>
 +     .---.---.
 +  20 |   | ● | 10
 +     .---.---.
 +  19 | ● | ● | 9
 +     .---.---.
 +  18 | ● | ● | 8
 +     .---.---.
 +  17 | ● | ● | 7
 +     .---.---.
 +  16 | ● | ● | 6
 +     .---.---.
 +  15 | ● | ● | 5
 +     .---.---.
 +  14 | ● | ● | 4
 +     .---.---.
 +  13 | ● | ● | 3
 +     .---.---.
 +  12 | ● | ● | 2
 +     .---.---.
 +  11 | ● | ■ | 1
 +     .---.---.
 +</a2s>
 +
 +==== Front USB 3.1 Gen 1 header (JP2) ====
 +<code>
 +1=USB30_PWR2
 +2=USB30_PWR2
 +3=USB30_PWR2
 +4=USB30_PWR2
 +5=USB3_1_RX_N
 +6=USB3_1_RX_P
 +7=GND
 +8=GND
 +9=USB3_1_TX_N
 +10=USB3_1_TX_P
 +11=GND
 +12=GND
 +13=USB2_1_N
 +14=USB2_1_P
 +15=USB30_PWR2
 +16=USB30_PWR2
 +17=USB30_PWR2
 +18=USB30_PWR2
 +19=USB3_2_RX_N
 +20=USB3_2_RX_P
 +21=GND
 +22=GND
 +23=USB3_2_TX_N
 +24=USB3_2_TX_P
 +25=GND
 +26=GND
 +27=USB2_2_N
 +28=USB2_2_P
 +29=GND
 +30=GND
 +</code>
 +<a2s>
 +      30              1
 +       ||||||||||||||||
 +   #-+-################-+-#
 +   | |                  | |
 +   | |                  | |
 + #-# #################### #-#
 + #--------------------------#
 +                      ↑
 +</a2s>
 +
 +==== Power switch & LED header (JP3) ====
 +<code>
 +1=+HD_LED
 +2=PWR_LED
 +3=-HD_LED
 +4=GND
 +5=RST_SW-
 +6=PWR_SW
 +7=GND
 +8=GND
 +9=NA
 +10=NULL
 +</code>
 +<a2s>
 +    9   7   5   3   1
 +  .---.---.---.---.---.
 +  | ● | ● | ● | ● | ■ |
 +  .---.---.---.---.---.
 +  |   | ● | ● | ● | ● |
 +  .---.---.---.---.---.
 +    10  8   6   4   2
 +</a2s>
 +
 +==== USB 2.0 connector (CN12) ====
 +<code>
 +1=GND
 +2=USB2P
 +3=USB2N
 +4=5V_DUAL
 +</code>
 +<a2s>
 + #-----------# 
 + |#-       -#|
 + ||         ||
 + |  ■ ● ● ●  |
 + || 4 3 2 1 ||
 + |#---------#|
 + #-----------#
 +</a2s>
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2019/07/09 10:05
  • by TS