Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
faq:xpc_cube:sh570r6 [2021/07/07 12:35] – created TSfaq:xpc_cube:sh570r6 [2022/03/08 16:03] (current) – [Clear CMOS & power button & +5V header (SW1)] TS
Line 1: Line 1:
 ====== SH570R6 ====== ====== SH570R6 ======
-There are no FAQ entries for this product yet.+{{section>faq:hardware:graphics#j-series_r-series_r4_r6&firstseconly&nofooter&noeditbutton&noreadmore}} 
 + 
 +===== TPM/MAC address update ===== 
 +**This update has two features:** 
 +  * If the installation of Windows 11 cannot be completed because errors such as "The PC must support TPM 2.0" are displayed, please perform the following steps. 
 +  * If the MAC addresses of the network cards soldered on the mainboard are incorrectly formatted or not accepted by the operating system, please perform the following steps. 
 + 
 +<WRAP important 40%> 
 +Please follow the steps in this exact order and do not skip any steps. 
 +</WRAP> 
 + 
 + 
 +==== Re-Flash BIOS ==== 
 +  - Re-Flash the BIOS v1.05 (or later if available) by USB drive (<wrap caution>even if 1.05 is already installed</wrap>): [[https://global.shuttle.com/products/productsDownload?productId=2593|Download BIOS]]\\ \\ <WRAP tip 40%>[[faq:hardware:bios#how_do_i_update_the_bios_version_in_uefi_uefi_mode|How do I update the BIOS version in UEFI (UEFI Mode)?]] 
 +</WRAP> 
 +   - After BIOS flash, please clear the CMOS via "Clear CMOS & power button (SW1)" 
 +     * <wrap caution>Disconnect the machine from power</wrap> and <wrap caution>shortcut the bottom pins (1 + 3)</wrap> on the backside <wrap caution>for at least 60 seconds</wrap> with a screwdriver, jumper or another metal part.\\ {{:faq:xpc_cube:sh570:remote_power_on_connector.jpg?nolink&300|}} 
 +     * Pinout:\\ <a2s> 
 +       SW1 
 +    .---.---. 
 +  2 | ● | ● | 4 
 +    .---.---. 
 +  1 | ■ | ● | 3 
 +    .---.---. 
 +</a2s> 
 +     * <wrap notice>NOTE:</wrap> The four pins may be covered. Please remove the plastic/mylar first. 
 +   - Now enter the BIOS again and press the following keys in order: ''F3'' -> ''ENTER'' -> ''F4'' -> ''ENTER'' 
 +   - After that, please install and run Windows and check for MAC address: 
 +     * Please download and run the "MAC address update tool" in Windows 10/11: [[https://share.shuttle.eu/index.php/s/yI818jIrEMMMMtC|Download tool]] 
 + 
 +==== How to use the MAC address update tool ==== 
 +  - Get the update tool from [[https://share.shuttle.eu/index.php/s/yI818jIrEMMMMtC|here]]. 
 +  - Start the update. 
 +  - Unpack the contents of the ZIP archive. 
 +  - Run ''sch_macupdate_x64.exe''. It lists all available network adapters.\\ {{:faq:xpc_cube:sh570:mac_update_tool01.png?nolink&500|}} 
 +  - A faulty adapter is marked red. To fix the MAC address (MAC-ID), click "Update".\\ {{:faq:xpc_cube:sh570:mac_update_tool02.png?nolink&500|}} 
 +  - After a few seconds, the update is done and all MAC addresses have been set to correct values again. 
 + 
 +**No network adapter found?**\\ {{:faq:xpc_cube:sh570:mac_update_tool03.png?nolink&500|}} 
 +  - If no network adapter is listed, close the tool. 
 +  - Execute ''install.bat'' batch file from the same folder to a driver setup. 
 +  - After finishing the driver installation, start ''sch_macupdate_x64.exe'' again. 
 + 
 +===== Jumper settings and pinout ===== 
 +==== Fan connectors (FAN1, FAN2) ==== 
 +<code> 
 +1=GND 
 +2=+12V 
 +3=FAN IO 
 +4=FAN PWM 
 +</code> 
 +<a2s> 
 +     FAN1           FAN2 
 +                  #------#  
 + #---------#      |   ■  | 4 
 +   ----- |      |   ■ || 3 
 + | ■ ■ ■ ■ |      |   ■ || 2 
 + | 4 3 2 1 |      |   ■ || 1 
 + #---------#      #------# 
 +</a2s> 
 + 
 +==== COM header (COM1) ==== 
 +<code> 
 +1=DCD 
 +2=RXD 
 +3=TXD 
 +4=DTR 
 +5=GND 
 +6=DSR 
 +7=RTS 
 +8=CTS 
 +9=-XRI1 
 +10=NULL 
 +</code> 
 +<a2s> 
 +    2         10 
 +  .---.---.---.---.---. 
 +  | ● | ● | ● | ● |   | 
 +  .---.---.---.---.---. 
 +  | ■ | ● | ● | ● | ● | 
 +  .---.---.---.---.---. 
 +    1         9 
 +</a2s> 
 + 
 +==== Clear CMOS, power button and +5V header (SW1) ==== 
 +<code> 
 +1=RTC Reset 
 +2=VCC_AUX 
 +3=GND 
 +4=Power SW 
 +</code> 
 + 
 +<a2s> 
 +       SW1 
 +    .---.---. 
 +  2 | ● | ● | 4 
 +    .---.---. 
 +  1 | ■ | ● | 3 
 +    .---.---. 
 +</a2s>
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2021/07/07 12:35
  • by TS