Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
faq:xpc_cube:st20g5 [2016/08/29 12:50] – Shuttlefaq:xpc_cube:st20g5 [2021/09/02 13:43] (current) – TS
Line 1: Line 1:
 ====== ST20G5 ====== ====== ST20G5 ======
-{{section>faq:xpc_cube:sg33g5#post_issuejp4_jumper_setting_for_shuttle_g5_models&firstseconly&nofooter&noeditbutton&noreadmore}} +{{section>faq:xpc_cube:sg33g5#post_issue_on_shuttle_g5_models_-_check_setting_of_jumper_jp4&firstseconly&nofooter&noeditbutton&noreadmore}} 
 +{{section>faq:hardware:graphics#g-series&firstseconly&nofooter&noeditbutton&noreadmore}}
 ===== Windows 2000 and XP installation on a Serial ATA(SATA)/RAID Hard Drive ===== ===== Windows 2000 and XP installation on a Serial ATA(SATA)/RAID Hard Drive =====
 To install an Windows 2000 or XP on a SATA/RAID hard drive, a floppy drive (or USB floppy drive) and floppy disk with the correct RAID drivers are essential. To install an Windows 2000 or XP on a SATA/RAID hard drive, a floppy drive (or USB floppy drive) and floppy disk with the correct RAID drivers are essential.
Line 22: Line 22:
     - Enter ''South Configuration'' \\ {{:faq:xpc_cube:st20:st20_raid_installation_07.jpg?nolink&400|}}     - Enter ''South Configuration'' \\ {{:faq:xpc_cube:st20:st20_raid_installation_07.jpg?nolink&400|}}
     - Enable ''Serial ATA RAID Mode'', press ''F10'' to save the configuration and exit. \\ {{:faq:xpc_cube:st20:st20_raid_installation_08.jpg?nolink&400|}}     - Enable ''Serial ATA RAID Mode'', press ''F10'' to save the configuration and exit. \\ {{:faq:xpc_cube:st20:st20_raid_installation_08.jpg?nolink&400|}}
-    - Press ''Ctrl-A'' to enter ULi RAID BIOS Setup Utility and select the drives that you wish to use in a RAID array. (Please refer to the ULi RAID manual P3).+    - Press ''Ctrl-A'' to enter ''ULi RAID BIOS Setup Utility'' and select the drives that you wish to use in a RAID array. (Please refer to the ULi RAID manual P3).
     - Installing Windows     - Installing Windows
     - The following procedure outlines the important steps in installing Windows on a RAID drive. Before you begin, please make sure the RAID driver disk is inserted in the floppy drive, and the floppy drive is connected to the computer.     - The following procedure outlines the important steps in installing Windows on a RAID drive. Before you begin, please make sure the RAID driver disk is inserted in the floppy drive, and the floppy drive is connected to the computer.
Line 30: Line 30:
     - Press "Enter" to select the ''ULi SATA Controller(M5287, Windows XP/Server 2003)''.     - Press "Enter" to select the ''ULi SATA Controller(M5287, Windows XP/Server 2003)''.
     - The following Windows Setup screen appears listing the drivers that you choose. \\ {{:faq:xpc_cube:st20:st20_raid_installation_12.jpg?nolink&400|}}     - The following Windows Setup screen appears listing the drivers that you choose. \\ {{:faq:xpc_cube:st20:st20_raid_installation_12.jpg?nolink&400|}}
-  - After the drivers are selected, press Enter to continue installing Windows. +    - After the drivers are selected, press Enter to continue installing Windows. 
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2016/08/29 12:50
  • by Shuttle