Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
faq:xpc_nano:nc03u [2018/04/11 08:50] – created Shuttlefaq:xpc_nano:nc03u [2019/07/24 10:02] (current) – [HDD Installation] christian
Line 1: Line 1:
 ====== NC03U ====== ====== NC03U ======
 {{section>faq:xpc_accessories:wln-m#upgrade_the_shuttle_nc03u_wlan_module_to_wln-m&firstseconly&nofooter&noeditbutton&noreadmore}} {{section>faq:xpc_accessories:wln-m#upgrade_the_shuttle_nc03u_wlan_module_to_wln-m&firstseconly&nofooter&noeditbutton&noreadmore}}
 +
 +===== Quick Installation Guide =====
 +==== Begin Installation =====
 +<WRAP important 60%>
 +The unit can be operated at a maximum ambient temperature of 50°C (122°F).\\ Do not expose it to temperatures below 0°C (32°F) or above 50°C (122°F).
 +</WRAP>
 +<WRAP important 60%>
 +For safety reasons, please ensure that the power cord is disconnected before opening the case.
 +</WRAP>
 +  - Unscrew two screws of the back cover and remove it.\\ {{:faq:xpc_nano:nc03:installation01.png?nolink&500|}}
 +
 +==== Memory Module Installation ====
 +<WRAP important 60%>
 +This motherboard does only support 1.2V DDR4 memory modules.
 +</WRAP>
 +  - Locate the SO-DIMM (DIMMB1) slot on the motherboard.\\ {{:faq:xpc_nano:nc03:installation02.png?nolink&500|}}
 +  - Align the notch of the memory module with the one of the memory slot.\\ {{:faq:xpc_nano:nc03:installation03.png?nolink&500|}}
 +  - Gently insert the memory module into the slot in a 45-degree angle.\\ {{:faq:xpc_nano:nc03:installation04.png?nolink&500|}}
 +  - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:faq:xpc_nano:nc03:installation05.png?nolink&500|}}
 +  * If the DIMMA1 slot should also be equipped with a memory module, please proceed with the following steps.
 +  - Turn your NC03U upside down and remove another cover.
 +  - Locate the SO-DIMM (DIMMA1) slot on the motherboard.\\ {{:faq:xpc_nano:nc03:installation06.png?nolink&500|}}
 +  - Install the memory module into the DIMMA1 slot.\\ {{:faq:xpc_nano:nc03:installation07.png?nolink&500|}}
 +
 +==== M.2 SSD Installation ====
 +  - Locate the M.2 slot on the motherboard and unfasten the screw first.\\ {{:faq:xpc_nano:nc03:installation08.png?nolink&500|}}
 +  - Install the M.2 SSD into the M.2 slot and secure with a screw.\\ {{:faq:xpc_nano:nc03:installation09.png?nolink&500|}}
 +  - Replace the cover and turn your NC03U upside down.\\ {{:faq:xpc_nano:nc03:installation10.png?nolink&500|}}
 +
 +==== Installation of 2.5'' Drive ====
 +<WRAP important 60%>
 +This model supports 2.5" drives (HDDs and SSDs) up to a thickness of 15mm.
 +</WRAP>
 +  - Mount the drive in the bracket with four screws.\\ {{:faq:xpc_nano:nc03:installation11.png?nolink&500|}}
 +  - Install the drive sitting in its bracket in the chassis and secure with four screws. Tear off the adhesive tape of the SATA cable.\\ {{:faq:xpc_nano:nc03:installation12.png?nolink&500|}}
 +  - Connect the drive with the cable.\\ {{:faq:xpc_nano:nc03:installation13.png?nolink&500|}}
 +  - Replace the cover and refasten the two screws.\\ {{:faq:xpc_nano:nc03:installation14.png?nolink&500|}}
 +
 +==== Connecting to Power ====
 +{{:faq:xpc_nano:nc03:installation16.png?nolink&500|}}
 +
 +<WRAP tip 60%>
 +Please press the ''Del'' key while booting to enter BIOS. Here, please load the optimised BIOS settings.
 +</WRAP>
 +
 +==== Using the Vertical Stand ====
 +  - Install the vertical stand and check that it is properly aligned, then tighten securely with four screws.\\ {{:faq:xpc_nano:nc03:installation17.png?nolink&500|}}
 +
 +==== Installation of VESA Mount ====
 +{{:faq:xpc_nano:nc03:installation18.png?nolink&500|}}
 +
 +{{:faq:xpc_nano:nc03:installation19.png?nolink&500|}}
 +
 +===== Jumper settings and pinout =====
 +==== AC Back Auto Power ON ====
 +<code>
 +1=AMP(+)
 +2=GND
 +</code>
 +<a2s>
 + Open (enabled)  Short (disabled)
 +
 +        JP1            JP1
 +     .---.---.       #------#
 +     | ■ | ● |       |[x]   |
 +     .---.---.       #------#
 +                   
 +[x]: {"stroke-width":4, "fill":"#999999", "a2s:delref":true}
 +</a2s>
 +
 +==== Clear CMOS ====
 +<code>
 +1=RTCRST
 +2=GND
 +</code>
 +<a2s>
 +    JP2
 + .---.---.
 + | ● | ■ |
 + .---.---.
 +     1
 +</a2s>
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2018/04/11 08:50
  • by Shuttle