Differences

This shows you the differences between two versions of the page.

Link to this comparison view

faq:xpc_nano:nc03u [2018/04/11 08:50]
Shuttle created
faq:xpc_nano:nc03u [2019/07/10 14:59] (current)
TS
Line 1: Line 1:
 ====== NC03U ====== ====== NC03U ======
 {{section>​faq:​xpc_accessories:​wln-m#​upgrade_the_shuttle_nc03u_wlan_module_to_wln-m&​firstseconly&​nofooter&​noeditbutton&​noreadmore}} {{section>​faq:​xpc_accessories:​wln-m#​upgrade_the_shuttle_nc03u_wlan_module_to_wln-m&​firstseconly&​nofooter&​noeditbutton&​noreadmore}}
 +
 +===== Quick Installation Guide =====
 +==== Begin Installation =====
 +<WRAP important 60%>
 +The unit can be operated at an ambient temperature of max. 50°C (122°F).\\ Do not expose it to temperatures below 0°C (32°F) or above 50°C (122°F).
 +</​WRAP>​
 +<WRAP important 60%>
 +For safety reasons, please ensure that the power cord is disconnected before opening the case.
 +</​WRAP>​
 +  - Unscrew two screws of the back cover and remove it.\\ {{:​faq:​xpc_nano:​nc03:​installation01.png?​nolink&​500|}}
 +
 +==== Memory Module Installation ====
 +<WRAP important 60%>
 +This motherboard does only support 1.2V DDR4 memory modules.
 +</​WRAP>​
 +  - Locate the SO-DIMM (DIMMB1) slot on the motherboard.\\ {{:​faq:​xpc_nano:​nc03:​installation02.png?​nolink&​500|}}
 +  - Align the notch of the memory module with the one of the memory slot.\\ {{:​faq:​xpc_nano:​nc03:​installation03.png?​nolink&​500|}}
 +  - Gently insert the memory module into the slot in a 45-degree angle.\\ {{:​faq:​xpc_nano:​nc03:​installation04.png?​nolink&​500|}}
 +  - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:​faq:​xpc_nano:​nc03:​installation05.png?​nolink&​500|}}
 +  * If the DIMMA1 slot should also be equipped with a memory module, please proceed with the following steps.
 +  - Turn your NC03U upside down and remove another cover.
 +  - Locate the SO-DIMM (DIMMA1) slot on the motherboard.\\ {{:​faq:​xpc_nano:​nc03:​installation06.png?​nolink&​500|}}
 +  - Install the memory module into the DIMMA1 slot.\\ {{:​faq:​xpc_nano:​nc03:​installation07.png?​nolink&​500|}}
 +
 +==== M.2 SSD Installation ====
 +  - Locate the M.2 slot on the motherboard and unfasten the screw first.\\ {{:​faq:​xpc_nano:​nc03:​installation08.png?​nolink&​500|}}
 +  - Install the M.2 SSD into the M.2 slot and secure with a screw.\\ {{:​faq:​xpc_nano:​nc03:​installation09.png?​nolink&​500|}}
 +  - Replace the cover and turn your NC03U upside down.\\ {{:​faq:​xpc_nano:​nc03:​installation10.png?​nolink&​500|}}
 +
 +==== HDD Installation ====
 +<WRAP important 60%>
 +This model supports 2.5" SATA HDDs up to a thickness of 15mm.
 +</​WRAP>​
 +  - Mount the HDD into the bracket with four screws.\\ {{:​faq:​xpc_nano:​nc03:​installation11.png?​nolink&​500|}}
 +  - Install the HDD with its bracket in the chassis with four screws and tear off the adhesive tape of the HDD cable.\\ {{:​faq:​xpc_nano:​nc03:​installation12.png?​nolink&​500|}}
 +  - Connect the HDD with HDD cable.\\ {{:​faq:​xpc_nano:​nc03:​installation13.png?​nolink&​500|}}
 +  - Replace the cover and refasten the two screws.\\ {{:​faq:​xpc_nano:​nc03:​installation14.png?​nolink&​500|}}
 +
 +==== Connecting to Power ====
 +{{:​faq:​xpc_nano:​nc03:​installation16.png?​nolink&​500|}}
 +
 +<WRAP tip 60%>
 +Please press the ''​Del''​ key while booting to enter BIOS. Here, please load the optimised BIOS settings.
 +</​WRAP>​
 +
 +==== Using the Vertical Stand ====
 +  - Install the vertical stand and check that it is properly aligned, then tighten securely with four screws.\\ {{:​faq:​xpc_nano:​nc03:​installation17.png?​nolink&​500|}}
 +
 +==== Installation of VESA Mount ====
 +{{:​faq:​xpc_nano:​nc03:​installation18.png?​nolink&​500|}}
 +
 +{{:​faq:​xpc_nano:​nc03:​installation19.png?​nolink&​500|}}
 +
 +===== Jumper settings and pinout =====
 +==== AC Back Auto Power ON ====
 +<​code>​
 +1=AMP(+)
 +2=GND
 +</​code>​
 +<a2s>
 + Open (enabled) ​ Short (disabled)
 +
 +        JP1            JP1
 +     ​.---.---. ​      #​------#​
 +     | ■ | ● |       ​|[x] ​  |
 +     ​.---.---. ​      #​------#​
 +       ​1 ​  ​2 ​          ​1 ​ 2 
 +[x]: {"​stroke-width":​4,​ "​fill":"#​999999",​ "​a2s:​delref":​true}
 +</​a2s>​
 +
 +==== Clear CMOS ====
 +<​code>​
 +1=RTCRST
 +2=GND
 +</​code>​
 +<a2s>
 +    JP2
 + ​.---.---.
 + | ● | ■ |
 + ​.---.---.
 +   ​2 ​  1
 +</​a2s>​
  
 ==== Related links ==== ==== Related links ====
 {{backlinks>​.}} {{backlinks>​.}}
  • faq/xpc_nano/nc03u.txt
  • Last modified: 2019/07/10 14:59
  • by TS