Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
Last revisionBoth sides next revision
faq:xpc_slim:dl10j [2019/01/31 17:20] – Shuttlefaq:xpc_slim:dl10j [2019/07/24 09:47] – [Begin Installation] christian
Line 19: Line 19:
 The first COM port is marked on this photo:\\ {{:faq:xpc_slim:dl10j:dl10j_com1.jpg?nolink&400|}} The first COM port is marked on this photo:\\ {{:faq:xpc_slim:dl10j:dl10j_com1.jpg?nolink&400|}}
  
 +===== Quick Installation Guide =====
 +==== Begin Installation ====
 +<WRAP important 60%>
 +For safety reasons, please ensure that the power cord is disconnected before opening the case.
 +</WRAP>
 +  - Unscrew the two screws of the chassis cover.\\ {{:faq:xpc_slim:dl10j:installation01.png?nolink&500|}}
 +  - Slide the cover backward and upward.\\ {{:faq:xpc_slim:dl10j:installation02.png?nolink&500|}}
 +  - Unfasten the rack mount screw and remove the drive holder.\\ {{:faq:xpc_slim:dl10j:installation03.png?nolink&500|}}
 +
 +==== Memory Module Installation ==== 
 +<WRAP important 60%>
 +This mainboard does only support 1.2 V DDR4 SO-DIMM memory modules.
 +</WRAP>
 +  - Locate the SO-DIMM slot on the mainboard.
 +  - Align the notch of the memory module with the one of the relevant memory slot.\\ {{:faq:xpc_slim:dl10j:installation04.png?nolink&500|}}
 +  - Gently insert the module into the slot in a 45-degree angle.\\ {{:faq:xpc_slim:dl10j:installation05.png?nolink&500|}}\\ {{:faq:xpc_slim:dl10j:installation06.png?nolink&500|}}
 +  - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:faq:xpc_slim:dl10j:installation07.png?nolink&500|}}
 +  - Repeat the above steps to install an additional memory module, if required.\\ {{:faq:xpc_slim:dl10j:installation08.png?nolink&500|}}
 +
 +==== Component Installation ====
 +  - Please proceed as shown in the illustration, and locate the M.2 key slot on the mainboard.\\ {{:faq:xpc_slim:dl10j:installation09.png?nolink&500|}}
 +  - Install the M.2 device into the M.2 slot and secure with the screw.\\ {{:faq:xpc_slim:dl10j:installation10.png?nolink&500|}}
 +  - Place an HDD or SSD in the rack and secure with the four screws from the sides.\\ {{:faq:xpc_slim:dl10j:installation11.png?nolink&500|}}
 +  - Connect the Serial ATA and power cable to the HDD or SSD. Slide the rack into the chassis and refasten the screws.\\ {{:faq:xpc_slim:dl10j:installation12.png?nolink&500|}}
 +
 +==== Complete ====
 +  - Replace the cover and refasten the screws.\\ {{:faq:xpc_slim:dl10j:installation13.png?nolink&500|}}
 +  - Screw the included antenna on to the appropriate connector at the back panel. Make sure it is aligned vertically or horizontally to achieve the best possible signal reception.\\ {{:faq:xpc_slim:dl10j:installation14.png?nolink&500|}}
 +  - Complete.
 +  - Please press the ''Del'' key while booting to enter BIOS. Here, please load the optimised BIOS settings.
 +
 +===== Jumper settings and pinout =====
 +==== SATA cable connector (SATA1) ====
 +<code>
 +1=NA
 +2=NA
 +3=NA
 +4=NA
 +5=GND
 +6=GND
 +7=GND
 +8=+5V
 +9=+5V
 +10=+5V
 +11=+5V
 +12=GND
 +13=GND
 +14=GND
 +15=SATA_TX_P
 +16=SATA_TX_N
 +17=GND
 +18=SATA_RX_N
 +19=SATA_RX_P
 +20=GND
 +</code>
 +<a2s>
 + #---------------------------#
 + |#-------------------------#|
 + ||  |||||||||||||||||||||  ||
 + |#--|||||||||||||||||||||--#|
 + |   |||||||||||||||||||||   |
 + #---------------------------#
 +     1                   20
 +     ↑
 +</a2s>
 +
 +==== AC back auto power on (JP1) ====
 +<code>
 +1=OP(+)
 +2=GND
 +</code>
 +<a2s>
 + Open (enabled)  Short (disabled)
 +
 +   .---.---.        #------#
 +   | ■ | ● |        |[x]   |
 +   .---.---.        #------#
 +     1   2            1  2 
 +[x]: {"stroke-width":4, "fill":"#999999", "a2s:delref":true}
 +</a2s>
 +
 +==== Clear CMOS & power button (SW1) ====
 +<code>
 +1=RTCRST
 +2=+5V
 +3=GND
 +4=PWRSW
 +</code>
 +<a2s>
 +       SW1
 +    .---.---.
 +  2 | ● | ● | 4
 +    .---.---.
 +  1 | ■ | ● | 3
 +    .---.---.
 +</a2s>
 +
 +==== Battery connector (CN9) ====
 +<code>
 +1=V_BAT
 +2=GND
 +</code>
 +<a2s>
 + #------#
 + |#----#|
 + || 2 ■||
 + |     ||
 + || 1 ■||
 + |#----#| ->
 + #------#
 +</a2s>
 +
 +==== Debug port (DBG1) ====
 +<code>
 +1=LPC_24M
 +2=LAD1
 +3=SIORST-
 +4=LAD0
 +5=LFRAME-
 +6=+3.3V
 +7=LAD3
 +8=GND
 +9=LAD2
 +10=NULL
 +</code>
 +<a2s>
 +        DBG1  
 +     .---.---.
 +  10 |   | ● | 9
 +     .---.---.
 +   8 | ● | ● | 7
 +     .---.---.
 +   6 | ● | ● | 5
 +     .---.---.
 +   4 | ● | ● | 3
 +     .---.---.
 +   1 | ● | ■ | 1
 +     .---.---.
 +</a2s>
 +
 +==== COM 1 & COM 2 power switch (JP2) ====
 +**COM PORT Pin 9 "Ring Indicator" (RI) configuration:**
 +
 +Configure COM 1 with the first jumper:
 +  * Short Pin 1-2: Pin 9 = RI (default)
 +  * Short Pin 5-7: Pin 9 = +5V
 +  * Short Pin 7-9: Pin 9 = +12V
 +
 +Configure COM 2 with the second jumper:
 +  * Short Pin 3-4: Pin 9 = RI (default)
 +  * Short Pin 6-8: Pin 9 = +5V
 +  * Short Pin 8-10: Pin 9 = +12V
 +<code>
 +1=-XRI1
 +2=COM_-XRI1
 +3=-XRI2
 +4=COM_-XRI2
 +5=+5V
 +6=+5V
 +7=COM1_PWR
 +8=COM2_PWR
 +9=+12V
 +10=+12V
 +</code>
 +<a2s>
 +   2   4   6   8   10
 + .---.---.---.---.---.
 + | ● | ● | ● | ● | ● |
 + .---.---.---.---.---.
 + | ■ | ● | ● | ● | ● |
 + .---.---.---.---.---.
 +   1   3   5   7   9
 +</a2s>
 +
 +==== COM port (COM 1, COM 2) ====
 +<code>
 +1=DCD
 +2=RX
 +3=TX
 +4=DTR
 +5=GND
 +6=DSR
 +7=RTS
 +8=CTS
 +9=RI
 +10=NULL
 +</code>
 +<a2s>
 +   2   4   6   8   10
 + .---.---.---.---.---.
 + | ● | ● | ● | ● |   |
 + .---.---.---.---.---.
 + | ■ | ● | ● | ● | ● |
 + .---.---.---.---.---.
 +   1   3   5   7   9
 +</a2s>
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2019/07/24 09:49
  • by christian