Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_slim:dl10j [2018/11/16 13:24] Shuttlefaq:xpc_slim:dl10j [2019/07/24 09:49] (current) – [Component Installation] christian
Line 1: Line 1:
 ====== DL10J ====== ====== DL10J ======
 {{section>faq:hardware:i_o#rs232_422_485_assignment&firstseconly&nofooter&noeditbutton&noreadmore}} {{section>faq:hardware:i_o#rs232_422_485_assignment&firstseconly&nofooter&noeditbutton&noreadmore}}
 +{{section>faq:xpc_accessories:wwn01#software_installation_and_first_connect_wwn01_lte_module_huawei_em906s_lte_module&firstseconly&nofooter&noeditbutton&noreadmore}}
  
 ===== Which LTE/4G modules are suitable? ===== ===== Which LTE/4G modules are suitable? =====
Line 10: Line 11:
 |Quectel|EM06-E|CAT 6, for EMEA, Australia, Brazil| |Quectel|EM06-E|CAT 6, for EMEA, Australia, Brazil|
  
 +===== LTE module cannot be found in the device manager? =====
 +Check the following BIOS setting to ensure that the LTE module will be recognized correctly.\\ Go to **Advanced** → **Onboard Device Configuration** → **E** → **Key Device Select** and change from ''PCIE'' to ''USB''
 +
 +{{:faq:xpc_slim:dl10j:lte_module_bios.jpg?nolink&400|}}
 +
 +===== Where is COM port #1? =====
 +The first COM port is marked on this photo:\\ {{:faq:xpc_slim:dl10j:dl10j_com1.jpg?nolink&400|}}
 +
 +===== Quick Installation Guide =====
 +==== Begin Installation ====
 +<WRAP important 60%>
 +For safety reasons, please ensure that the power cord is disconnected before opening the case.
 +</WRAP>
 +  - Unscrew the two screws of the chassis cover.\\ {{:faq:xpc_slim:dl10j:installation01.png?nolink&500|}}
 +  - Slide the cover backward and upward.\\ {{:faq:xpc_slim:dl10j:installation02.png?nolink&500|}}
 +  - Unfasten the rack mount screw and remove the drive holder.\\ {{:faq:xpc_slim:dl10j:installation03.png?nolink&500|}}
 +
 +==== Memory Module Installation ==== 
 +<WRAP important 60%>
 +This mainboard does only support 1.2 V DDR4 SO-DIMM memory modules.
 +</WRAP>
 +  - Locate the SO-DIMM slot on the mainboard.
 +  - Align the notch of the memory module with the one of the relevant memory slot.\\ {{:faq:xpc_slim:dl10j:installation04.png?nolink&500|}}
 +  - Gently insert the module into the slot in a 45-degree angle.\\ {{:faq:xpc_slim:dl10j:installation05.png?nolink&500|}}\\ {{:faq:xpc_slim:dl10j:installation06.png?nolink&500|}}
 +  - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:faq:xpc_slim:dl10j:installation07.png?nolink&500|}}
 +  - Repeat the above steps to install an additional memory module, if required.\\ {{:faq:xpc_slim:dl10j:installation08.png?nolink&500|}}
 +
 +==== Component Installation ====
 +  - Please proceed as shown in the illustration, and locate the M.2 key slot on the mainboard.\\ {{:faq:xpc_slim:dl10j:installation09.png?nolink&500|}}
 +  - Install the M.2 device in the M.2 slot and secure with the screw.\\ {{:faq:xpc_slim:dl10j:installation10.png?nolink&500|}}
 +  - Place an HDD or SSD in the rack and secure with four screws from the sides.\\ {{:faq:xpc_slim:dl10j:installation11.png?nolink&500|}}
 +  - Connect the Serial ATA and power cable to the HDD or SSD. Slide the rack into the chassis and refasten the screws.\\ {{:faq:xpc_slim:dl10j:installation12.png?nolink&500|}}
 +
 +==== Complete ====
 +  - Replace the cover and refasten the screws.\\ {{:faq:xpc_slim:dl10j:installation13.png?nolink&500|}}
 +  - Screw the included antenna on to the appropriate connector at the back panel. Make sure it is aligned vertically or horizontally to achieve the best possible signal reception.\\ {{:faq:xpc_slim:dl10j:installation14.png?nolink&500|}}
 +  - Complete.
 +  - Please press the ''Del'' key while booting to enter BIOS. Here, please load the optimised BIOS settings.
 +
 +===== Jumper settings and pinout =====
 +==== SATA cable connector (SATA1) ====
 +<code>
 +1=NA
 +2=NA
 +3=NA
 +4=NA
 +5=GND
 +6=GND
 +7=GND
 +8=+5V
 +9=+5V
 +10=+5V
 +11=+5V
 +12=GND
 +13=GND
 +14=GND
 +15=SATA_TX_P
 +16=SATA_TX_N
 +17=GND
 +18=SATA_RX_N
 +19=SATA_RX_P
 +20=GND
 +</code>
 +<a2s>
 + #---------------------------#
 + |#-------------------------#|
 + ||  |||||||||||||||||||||  ||
 + |#--|||||||||||||||||||||--#|
 +   |||||||||||||||||||||   |
 + #---------------------------#
 +                       20
 +     ↑
 +</a2s>
 +
 +==== AC back auto power on (JP1) ====
 +<code>
 +1=OP(+)
 +2=GND
 +</code>
 +<a2s>
 + Open (enabled)  Short (disabled)
 +
 +   .---.---.        #------#
 +   | ■ | ● |        |[x]   |
 +   .---.---.        #------#
 +                  1  2 
 +[x]: {"stroke-width":4, "fill":"#999999", "a2s:delref":true}
 +</a2s>
 +
 +==== Clear CMOS & power button (SW1) ====
 +<code>
 +1=RTCRST
 +2=+5V
 +3=GND
 +4=PWRSW
 +</code>
 +<a2s>
 +       SW1
 +    .---.---.
 +  2 | ● | ● | 4
 +    .---.---.
 +  1 | ■ | ● | 3
 +    .---.---.
 +</a2s>
 +
 +==== Battery connector (CN9) ====
 +<code>
 +1=V_BAT
 +2=GND
 +</code>
 +<a2s>
 + #------#
 + |#----#|
 + || 2 ■||
 +     ||
 + || 1 ■||
 + |#----#| ->
 + #------#
 +</a2s>
 +
 +==== Debug port (DBG1) ====
 +<code>
 +1=LPC_24M
 +2=LAD1
 +3=SIORST-
 +4=LAD0
 +5=LFRAME-
 +6=+3.3V
 +7=LAD3
 +8=GND
 +9=LAD2
 +10=NULL
 +</code>
 +<a2s>
 +        DBG1  
 +     .---.---.
 +  10 |   | ● | 9
 +     .---.---.
 +   8 | ● | ● | 7
 +     .---.---.
 +   6 | ● | ● | 5
 +     .---.---.
 +   4 | ● | ● | 3
 +     .---.---.
 +   1 | ● | ■ | 1
 +     .---.---.
 +</a2s>
 +
 +==== COM 1 & COM 2 power switch (JP2) ====
 +**COM PORT Pin 9 "Ring Indicator" (RI) configuration:**
 +
 +Configure COM 1 with the first jumper:
 +  * Short Pin 1-2: Pin 9 = RI (default)
 +  * Short Pin 5-7: Pin 9 = +5V
 +  * Short Pin 7-9: Pin 9 = +12V
 +
 +Configure COM 2 with the second jumper:
 +  * Short Pin 3-4: Pin 9 = RI (default)
 +  * Short Pin 6-8: Pin 9 = +5V
 +  * Short Pin 8-10: Pin 9 = +12V
 +<code>
 +1=-XRI1
 +2=COM_-XRI1
 +3=-XRI2
 +4=COM_-XRI2
 +5=+5V
 +6=+5V
 +7=COM1_PWR
 +8=COM2_PWR
 +9=+12V
 +10=+12V
 +</code>
 +<a2s>
 +           10
 + .---.---.---.---.---.
 + | ● | ● | ● | ● | ● |
 + .---.---.---.---.---.
 + | ■ | ● | ● | ● | ● |
 + .---.---.---.---.---.
 +           9
 +</a2s>
 +
 +==== COM port (COM 1, COM 2) ====
 +<code>
 +1=DCD
 +2=RX
 +3=TX
 +4=DTR
 +5=GND
 +6=DSR
 +7=RTS
 +8=CTS
 +9=RI
 +10=NULL
 +</code>
 +<a2s>
 +           10
 + .---.---.---.---.---.
 + | ● | ● | ● | ● |   |
 + .---.---.---.---.---.
 + | ■ | ● | ● | ● | ● |
 + .---.---.---.---.---.
 +           9
 +</a2s>
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2018/11/16 13:24
  • by Shuttle