Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_slim:dl10j [2019/01/31 17:20]
Shuttle
faq:xpc_slim:dl10j [2019/07/24 09:49] (current)
CS [Component Installation]
Line 19: Line 19:
 The first COM port is marked on this photo:\\ {{:​faq:​xpc_slim:​dl10j:​dl10j_com1.jpg?​nolink&​400|}} The first COM port is marked on this photo:\\ {{:​faq:​xpc_slim:​dl10j:​dl10j_com1.jpg?​nolink&​400|}}
  
 +===== Quick Installation Guide =====
 +==== Begin Installation ====
 +<WRAP important 60%>
 +For safety reasons, please ensure that the power cord is disconnected before opening the case.
 +</​WRAP>​
 +  - Unscrew the two screws of the chassis cover.\\ {{:​faq:​xpc_slim:​dl10j:​installation01.png?​nolink&​500|}}
 +  - Slide the cover backward and upward.\\ {{:​faq:​xpc_slim:​dl10j:​installation02.png?​nolink&​500|}}
 +  - Unfasten the rack mount screw and remove the drive holder.\\ {{:​faq:​xpc_slim:​dl10j:​installation03.png?​nolink&​500|}}
 +
 +==== Memory Module Installation ==== 
 +<WRAP important 60%>
 +This mainboard does only support 1.2 V DDR4 SO-DIMM memory modules.
 +</​WRAP>​
 +  - Locate the SO-DIMM slot on the mainboard.
 +  - Align the notch of the memory module with the one of the relevant memory slot.\\ {{:​faq:​xpc_slim:​dl10j:​installation04.png?​nolink&​500|}}
 +  - Gently insert the module into the slot in a 45-degree angle.\\ {{:​faq:​xpc_slim:​dl10j:​installation05.png?​nolink&​500|}}\\ {{:​faq:​xpc_slim:​dl10j:​installation06.png?​nolink&​500|}}
 +  - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:​faq:​xpc_slim:​dl10j:​installation07.png?​nolink&​500|}}
 +  - Repeat the above steps to install an additional memory module, if required.\\ {{:​faq:​xpc_slim:​dl10j:​installation08.png?​nolink&​500|}}
 +
 +==== Component Installation ====
 +  - Please proceed as shown in the illustration,​ and locate the M.2 key slot on the mainboard.\\ {{:​faq:​xpc_slim:​dl10j:​installation09.png?​nolink&​500|}}
 +  - Install the M.2 device in the M.2 slot and secure with the screw.\\ {{:​faq:​xpc_slim:​dl10j:​installation10.png?​nolink&​500|}}
 +  - Place an HDD or SSD in the rack and secure with four screws from the sides.\\ {{:​faq:​xpc_slim:​dl10j:​installation11.png?​nolink&​500|}}
 +  - Connect the Serial ATA and power cable to the HDD or SSD. Slide the rack into the chassis and refasten the screws.\\ {{:​faq:​xpc_slim:​dl10j:​installation12.png?​nolink&​500|}}
 +
 +==== Complete ====
 +  - Replace the cover and refasten the screws.\\ {{:​faq:​xpc_slim:​dl10j:​installation13.png?​nolink&​500|}}
 +  - Screw the included antenna on to the appropriate connector at the back panel. Make sure it is aligned vertically or horizontally to achieve the best possible signal reception.\\ {{:​faq:​xpc_slim:​dl10j:​installation14.png?​nolink&​500|}}
 +  - Complete.
 +  - Please press the ''​Del''​ key while booting to enter BIOS. Here, please load the optimised BIOS settings.
 +
 +===== Jumper settings and pinout =====
 +==== SATA cable connector (SATA1) ====
 +<​code>​
 +1=NA
 +2=NA
 +3=NA
 +4=NA
 +5=GND
 +6=GND
 +7=GND
 +8=+5V
 +9=+5V
 +10=+5V
 +11=+5V
 +12=GND
 +13=GND
 +14=GND
 +15=SATA_TX_P
 +16=SATA_TX_N
 +17=GND
 +18=SATA_RX_N
 +19=SATA_RX_P
 +20=GND
 +</​code>​
 +<a2s>
 + #​---------------------------#​
 + ​|#​-------------------------#​|
 + ​|| ​ ||||||||||||||||||||| ​ ||
 + ​|#​--|||||||||||||||||||||--#​|
 + ​| ​  ​||||||||||||||||||||| ​  |
 + #​---------------------------#​
 +     ​1 ​                  20
 +     ↑
 +</​a2s>​
 +
 +==== AC back auto power on (JP1) ====
 +<​code>​
 +1=OP(+)
 +2=GND
 +</​code>​
 +<a2s>
 + Open (enabled) ​ Short (disabled)
 +
 +   ​.---.---. ​       #------#
 +   | ■ | ● |        |[x]   |
 +   ​.---.---. ​       #------#
 +     ​1 ​  ​2 ​           1  2 
 +[x]: {"​stroke-width":​4,​ "​fill":"#​999999",​ "​a2s:​delref":​true}
 +</​a2s>​
 +
 +==== Clear CMOS & power button (SW1) ====
 +<​code>​
 +1=RTCRST
 +2=+5V
 +3=GND
 +4=PWRSW
 +</​code>​
 +<a2s>
 +       SW1
 +    .---.---.
 +  2 | ● | ● | 4
 +    .---.---.
 +  1 | ■ | ● | 3
 +    .---.---.
 +</​a2s>​
 +
 +==== Battery connector (CN9) ====
 +<​code>​
 +1=V_BAT
 +2=GND
 +</​code>​
 +<a2s>
 + #​------#​
 + ​|#​----#​|
 + || 2 ■||
 + ​| ​    ||
 + || 1 ■||
 + ​|#​----#​| ->
 + #​------#​
 +</​a2s>​
 +
 +==== Debug port (DBG1) ====
 +<​code>​
 +1=LPC_24M
 +2=LAD1
 +3=SIORST-
 +4=LAD0
 +5=LFRAME-
 +6=+3.3V
 +7=LAD3
 +8=GND
 +9=LAD2
 +10=NULL
 +</​code>​
 +<a2s>
 +        DBG1  ​
 +     ​.---.---.
 +  10 |   | ● | 9
 +     ​.---.---.
 +   8 | ● | ● | 7
 +     ​.---.---.
 +   6 | ● | ● | 5
 +     ​.---.---.
 +   4 | ● | ● | 3
 +     ​.---.---.
 +   1 | ● | ■ | 1
 +     ​.---.---.
 +</​a2s>​
 +
 +==== COM 1 & COM 2 power switch (JP2) ====
 +**COM PORT Pin 9 "Ring Indicator"​ (RI) configuration:​**
 +
 +Configure COM 1 with the first jumper:
 +  * Short Pin 1-2: Pin 9 = RI (default)
 +  * Short Pin 5-7: Pin 9 = +5V
 +  * Short Pin 7-9: Pin 9 = +12V
 +
 +Configure COM 2 with the second jumper:
 +  * Short Pin 3-4: Pin 9 = RI (default)
 +  * Short Pin 6-8: Pin 9 = +5V
 +  * Short Pin 8-10: Pin 9 = +12V
 +<​code>​
 +1=-XRI1
 +2=COM_-XRI1
 +3=-XRI2
 +4=COM_-XRI2
 +5=+5V
 +6=+5V
 +7=COM1_PWR
 +8=COM2_PWR
 +9=+12V
 +10=+12V
 +</​code>​
 +<a2s>
 +   ​2 ​  ​4 ​  ​6 ​  ​8 ​  10
 + ​.---.---.---.---.---.
 + | ● | ● | ● | ● | ● |
 + ​.---.---.---.---.---.
 + | ■ | ● | ● | ● | ● |
 + ​.---.---.---.---.---.
 +   ​1 ​  ​3 ​  ​5 ​  ​7 ​  9
 +</​a2s>​
 +
 +==== COM port (COM 1, COM 2) ====
 +<​code>​
 +1=DCD
 +2=RX
 +3=TX
 +4=DTR
 +5=GND
 +6=DSR
 +7=RTS
 +8=CTS
 +9=RI
 +10=NULL
 +</​code>​
 +<a2s>
 +   ​2 ​  ​4 ​  ​6 ​  ​8 ​  10
 + ​.---.---.---.---.---.
 + | ● | ● | ● | ● |   |
 + ​.---.---.---.---.---.
 + | ■ | ● | ● | ● | ● |
 + ​.---.---.---.---.---.
 +   ​1 ​  ​3 ​  ​5 ​  ​7 ​  9
 +</​a2s>​
 ==== Related links ==== ==== Related links ====
 {{backlinks>​.}} {{backlinks>​.}}
  • faq/xpc_slim/dl10j.1548955215.txt.gz
  • Last modified: 2019/01/31 17:20
  • by Shuttle