Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
faq:xpc_slim:ds77u [2017/06/20 09:21] – created MB | faq:xpc_slim:ds77u [2019/07/24 09:46] (current) – [DisplayPort restrictions of the DS77 Series] christian | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== DS77U ====== | ====== DS77U ====== | ||
- | ===== Frage hier ===== | + | ===== DisplayPort restrictions of the DS77 Series |
- | Antwort hier | + | The DS77U Series can be used with up to three displays simultaneously. Due to the design of the Intel chipset, please be aware of the following restrictions when setting up your monitor. |
+ | * The DisplayPort (DP) has **no audio** function. Please use **HDMI** for displays/ | ||
+ | * Intel **Collage Mode** is not available. Please use a native 4K display. Older monitors using Collage Mode are not supported. | ||
+ | * **PASSIVE adapters/ | ||
+ | * **HotPlug** is not supported. Please restart the system for the display to be detected. | ||
+ | **Note:** In a 3-display setup, the DP output will show no picture while booting in BIOS mode. It will be activated once the OS has loaded the display driver. | ||
- | (Oder: This product has no individual FAQs yet. Please have a look at the backlinks below to find other pages mentioning | + | ===== Quick Installation Guide ===== |
- | (Oder: [ganz an den Anfang stellen] | + | ==== Begin Installation ==== |
+ | <WRAP important 60%> | ||
+ | For safety reasons, please ensure that the power cord is disconnected before opening the case. | ||
+ | </ | ||
+ | - Unscrew two screws of the chassis cover.\\ {{:faq: | ||
+ | - Slide the cover forward and upward.\\ {{: | ||
+ | |||
+ | ==== Memory Module Installation ==== | ||
+ | <WRAP important 60%> | ||
+ | This mainboard does only support 1.2 V DDR4 SO-DIMM memory modules. | ||
+ | </ | ||
+ | - Locate the SO-DIMM slots on the mainboard. | ||
+ | - Align the notch of the memory module with the one of the memory slot.\\ {{: | ||
+ | - Gently insert the module into the slot in a 45-degree angle. | ||
+ | - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{: | ||
+ | - Repeat above steps to install additional memory modules, if desired. | ||
+ | |||
+ | ==== Mass Storage Installation ==== | ||
+ | === 2.5" HDD/SSD drive === | ||
+ | - Separate the rack from the chassis by undoing one screw.\\ {{:faq: | ||
+ | - Place the HDD or SSD in the rack and secure with two screws, one on each side.\\ | ||
+ | - Place the HDD or SSD in the drive bay and push it gently to the right until it clicks into place.\\ {{: | ||
+ | - Refasten the screws.\\ {{: | ||
+ | === M.2 SSD module === | ||
+ | - As shown, unfasten the screw first. | ||
+ | - Install the M.2 card into its slot and secure with the mentioned screw.\\ {{: | ||
+ | |||
+ | ==== Complete ==== | ||
+ | - Replace the covers and refasten the screws.\\ {{: | ||
+ | - Complete | ||
+ | <WRAP important 60%> | ||
+ | Please press the " | ||
+ | </ | ||
+ | |||
+ | ===== Jumper settings and pinout ===== | ||
+ | ==== COM Port 1 ==== | ||
+ | {{: | ||
+ | ^COM1 (RS232)^^^^ | ||
+ | ^Pin^Signal Name^Pin^Signal Name^ | ||
+ | |1|DCD|2|RX| | ||
+ | |3|TX|4|DTR| | ||
+ | |5|GND|6|DSR| | ||
+ | |7|RTS|8|CTS| | ||
+ | |9|RI1-| | | | ||
+ | ^COM1 (RS422)^^^^ | ||
+ | ^Pin^Signal Name^Pin^Signal Name^ | ||
+ | |1|TXD-|2|TXD+| | ||
+ | |3|RXD-|4|RXD+| | ||
+ | |5|GND|6|-| | ||
+ | |7|-|8|-| | ||
+ | |9|-| | | | ||
+ | ^COM1 (RS485)^^^^ | ||
+ | ^Pin^Signal Name^Pin^Signal Name^ | ||
+ | |1|Data-|2|Data+| | ||
+ | |3|-|4|-| | ||
+ | |5|GND|6|-| | ||
+ | |7|-8|-| | | ||
+ | |9|-| | | | ||
+ | ==== COM 1 & COM 2 Power Switch ==== | ||
+ | COM PORT Pin 9 "Ring Indicator" | ||
+ | < | ||
+ | 2 | ||
+ | .---.---.---.---.---. | ||
+ | | ● | ● | ● | ● | ● | | ||
+ | | ||
+ | | ■ | ● | ● | ● | ● | | ||
+ | .---.---.---.---.---. | ||
+ | 1 | ||
+ | </ | ||
+ | |||
+ | ^JP1^^^^ | ||
+ | ^COM1 (pin 9)^^COM2 (pin 9)^^ | ||
+ | ^Short Pin^Function^Short Pin^Function^ | ||
+ | |1-2 (Default)|RI1|3-4 (Default)|RI2| | ||
+ | |5-7|+5V|6-8|+5V| | ||
+ | |7-9|+12V|8-10|+12V| | ||
+ | |||
+ | ==== AC Back Auto Power ON ==== | ||
+ | ^JP9^^ | ||
+ | ^Pin^AC Back auto Power ON function^ | ||
+ | |Short 1-2|Disable (Default)| | ||
+ | |Open|Enable| | ||
+ | |||
+ | < | ||
+ | Open (enabled) | ||
+ | | ||
+ | | ● | 2 |[x]| 2 | ||
+ | | ||
+ | | ■ | 1 | | 1 | ||
+ | | ||
+ | JP9 JP9 | ||
+ | [x]: {" | ||
+ | </ | ||
+ | |||
+ | ==== External Power SW & Clear CMOS ==== | ||
+ | ^SW2^^ | ||
+ | ^Pin^Signal Name^ | ||
+ | |1|PWRSW| | ||
+ | |2|+5V| | ||
+ | |3|GND| | ||
+ | |4|RTC_RST# | ||
+ | |||
+ | < | ||
+ | | ||
+ | | ||
+ | | ● | ● | | ||
+ | | ||
+ | | ■ | ● | | ||
+ | | ||
+ | | ||
+ | </ | ||
+ | |||
+ | ===== Operating Position ===== | ||
+ | Please make sure to use either the supplied feet or the VESA mount. | ||
==== Related links ==== | ==== Related links ==== | ||
{{backlinks> | {{backlinks> |