Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
faq:xpc_slim:ds77u [2017/06/20 09:46] – MB | faq:xpc_slim:ds77u [2019/07/24 09:46] (current) – [DisplayPort restrictions of the DS77 Series] christian | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== DS77U ====== | ====== DS77U ====== | ||
- | ===== DS77 series Displayport | + | ===== DisplayPort |
+ | The DS77U Series can be used with up to three displays simultaneously. Due to the design of the Intel chipset, please be aware of the following restrictions when setting up your monitor. | ||
+ | * The DisplayPort (DP) has **no audio** function. Please use **HDMI** for displays/ | ||
+ | * Intel **Collage Mode** is not available. Please use a native 4K display. Older monitors using Collage Mode are not supported. | ||
+ | * **PASSIVE adapters/ | ||
+ | * **HotPlug** is not supported. Please restart the system for the display to be detected. | ||
+ | **Note:** In a 3-display setup, the DP output will show no picture while booting in BIOS mode. It will be activated once the OS has loaded the display driver. | ||
- | DS77U series can be used with 3 displays simultaneously. Due to Intel chipset design, please | + | ===== Quick Installation Guide ===== |
+ | ==== Begin Installation ==== | ||
+ | <WRAP important 60%> | ||
+ | For safety reasons, please | ||
+ | </ | ||
+ | - Unscrew two screws | ||
+ | - Slide the cover forward and upward.\\ {{: | ||
- | - Intel **Collage Mode** is not available. Please use a native 4K display. Old monitors with Collage Mode are not supported. | + | ==== Memory Module Installation ==== |
- | - **PASSIVE Adapter/ | + | <WRAP important 60%> |
+ | This mainboard does only support 1.2 V DDR4 SO-DIMM memory modules. | ||
+ | </ | ||
+ | - Locate the SO-DIMM slots on the mainboard. | ||
+ | - Align the notch of the memory module with the one of the memory slot.\\ {{: | ||
+ | | ||
+ | - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{: | ||
+ | - Repeat above steps to install additional memory modules, if desired. | ||
- | **Note:** In a 3-display setup, the DP output won't show a picture | + | ==== Mass Storage Installation ==== |
+ | === 2.5" HDD/SSD drive === | ||
+ | - Separate the rack from the chassis by undoing one screw.\\ {{:faq: | ||
+ | | ||
+ | - Place the HDD or SSD in the drive bay and push it gently to the right until it clicks into place.\\ {{: | ||
+ | - Refasten the screws.\\ {{: | ||
+ | === M.2 SSD module === | ||
+ | - As shown, unfasten the screw first. | ||
+ | - Install the M.2 card into its slot and secure with the mentioned screw.\\ {{: | ||
+ | |||
+ | ==== Complete ==== | ||
+ | - Replace the covers and refasten the screws.\\ {{: | ||
+ | - Complete | ||
+ | <WRAP important 60%> | ||
+ | Please press the " | ||
+ | </ | ||
+ | |||
+ | ===== Jumper settings and pinout ===== | ||
+ | ==== COM Port 1 ==== | ||
+ | {{: | ||
+ | ^COM1 (RS232)^^^^ | ||
+ | ^Pin^Signal Name^Pin^Signal Name^ | ||
+ | |1|DCD|2|RX| | ||
+ | |3|TX|4|DTR| | ||
+ | |5|GND|6|DSR| | ||
+ | |7|RTS|8|CTS| | ||
+ | |9|RI1-| | | | ||
+ | ^COM1 (RS422)^^^^ | ||
+ | ^Pin^Signal Name^Pin^Signal Name^ | ||
+ | |1|TXD-|2|TXD+| | ||
+ | |3|RXD-|4|RXD+| | ||
+ | |5|GND|6|-| | ||
+ | |7|-|8|-| | ||
+ | |9|-| | | | ||
+ | ^COM1 (RS485)^^^^ | ||
+ | ^Pin^Signal Name^Pin^Signal Name^ | ||
+ | |1|Data-|2|Data+| | ||
+ | |3|-|4|-| | ||
+ | |5|GND|6|-| | ||
+ | |7|-8|-| | | ||
+ | |9|-| | | | ||
+ | ==== COM 1 & COM 2 Power Switch ==== | ||
+ | COM PORT Pin 9 "Ring Indicator" | ||
+ | < | ||
+ | 2 | ||
+ | .---.---.---.---.---. | ||
+ | | ● | ● | ● | ● | ● | | ||
+ | | ||
+ | | ■ | ● | ● | ● | ● | | ||
+ | .---.---.---.---.---. | ||
+ | 1 | ||
+ | </ | ||
+ | |||
+ | ^JP1^^^^ | ||
+ | ^COM1 (pin 9)^^COM2 (pin 9)^^ | ||
+ | ^Short Pin^Function^Short Pin^Function^ | ||
+ | |1-2 (Default)|RI1|3-4 (Default)|RI2| | ||
+ | |5-7|+5V|6-8|+5V| | ||
+ | |7-9|+12V|8-10|+12V| | ||
+ | |||
+ | ==== AC Back Auto Power ON ==== | ||
+ | ^JP9^^ | ||
+ | ^Pin^AC Back auto Power ON function^ | ||
+ | |Short 1-2|Disable (Default)| | ||
+ | |Open|Enable| | ||
+ | |||
+ | < | ||
+ | Open (enabled) | ||
+ | | ||
+ | | ● | 2 |[x]| 2 | ||
+ | | ||
+ | | ■ | 1 | | 1 | ||
+ | | ||
+ | JP9 JP9 | ||
+ | [x]: {" | ||
+ | </ | ||
+ | |||
+ | ==== External Power SW & Clear CMOS ==== | ||
+ | ^SW2^^ | ||
+ | ^Pin^Signal Name^ | ||
+ | |1|PWRSW| | ||
+ | |2|+5V| | ||
+ | |3|GND| | ||
+ | |4|RTC_RST# | ||
+ | |||
+ | < | ||
+ | | ||
+ | | ||
+ | | ● | ● | | ||
+ | | ||
+ | | ■ | ● | | ||
+ | | ||
+ | | ||
+ | </ | ||
+ | |||
+ | ===== Operating Position ===== | ||
+ | Please make sure to use either the supplied feet or the VESA mount. | ||
==== Related links ==== | ==== Related links ==== | ||
{{backlinks> | {{backlinks> |