Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
faq:xpc_slim:xh110g [2019/07/04 14:45] – TS | faq:xpc_slim:xh110g [2021/09/02 13:29] (current) – TS | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== XH110G ====== | ====== XH110G ====== | ||
- | ===== What' | + | {{page> |
+ | |||
+ | ===== What is the maximum permitted size an internal USB device may have? ===== | ||
The maximum permitted size is 11.5 x 28 x 88 mm. | The maximum permitted size is 11.5 x 28 x 88 mm. | ||
===== What are the maximum dimensions a PCIe card may have? ===== | ===== What are the maximum dimensions a PCIe card may have? ===== | ||
Line 6: | Line 8: | ||
===== Quick Installation Guide ===== | ===== Quick Installation Guide ===== | ||
- | ==== Begin Installation | + | ==== Begin Installation ==== |
- Unscrew the two thumbscrews of the chassis cover.\\ {{: | - Unscrew the two thumbscrews of the chassis cover.\\ {{: | ||
- Slide the cover backwards and upwards.\\ {{: | - Slide the cover backwards and upwards.\\ {{: | ||
==== CPU/M.2 Card and ICE Module Installation ===== | ==== CPU/M.2 Card and ICE Module Installation ===== | ||
- Unfasten the four ICE module attachment screws.\\ {{: | - Unfasten the four ICE module attachment screws.\\ {{: | ||
- | - Remove | + | - Take the ICE module |
- | This 1151-pin socket is fragile and easily damaged. Always use extreme care when installing a CPU and limit the number of times that you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. | + | This 1151-pin socket is fragile and easily damaged. Always use extreme care when installing a CPU and limit the number of times you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. |
- | </ | + | </ |
- First unlock and raise the socket lever.\\ {{: | - First unlock and raise the socket lever.\\ {{: | ||
- Tear off the protective membrane from the metal load plate. Lift the metal load plate off the CPU socket.\\ {{: | - Tear off the protective membrane from the metal load plate. Lift the metal load plate off the CPU socket.\\ {{: | ||
- | DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed. | + | DO NOT touch the socket contacts. To protect the CPU socket, always replace the protective socket cover when a CPU is not installed. |
</ | </ | ||
- | - Orientate the CPU and socket, please align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then insert | + | - Orientate the CPU properly by aligning |
- | Please be aware of the CPU orientation, | + | Please be aware of the CPU orientation, |
</ | </ | ||
- Close the metal load plate, lower the CPU socket lever and lock in place. | - Close the metal load plate, lower the CPU socket lever and lock in place. | ||
Line 25: | Line 27: | ||
Please do not apply excess amount of thermal paste. | Please do not apply excess amount of thermal paste. | ||
</ | </ | ||
- | - As shown in Illustration.\\ {{: | + | - Please look at the illustration below.\\ {{: |
- Install the M.2 card into the M.2 slot and secure with the screw.\\ {{: | - Install the M.2 card into the M.2 slot and secure with the screw.\\ {{: | ||
- | - Screw the ICE module to the mainboard.\\ {{: | + | - Screw the ICE module |
==== Memory Module Installation ==== | ==== Memory Module Installation ==== | ||
<WRAP important 60%> | <WRAP important 60%> | ||
This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules. | This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules. | ||
</ | </ | ||
- | - Locate the SO-DIMM | + | - Locate the two SO-DIMM |
- | - Align the notch of the memory module with the one of the memory slot.\\ {{: | + | - Align the notch of the memory module with the one of the relevant |
- Gently insert the module into the slot in a 45-degree angle. | - Gently insert the module into the slot in a 45-degree angle. | ||
- Carefully push down the memory module until it snaps into the locking mechanism.\\ {{: | - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{: | ||
- | - Repeat the above steps to install additional memory | + | - Repeat the above steps to install |
- | ==== Installation of Expansion Card ==== | + | ==== Installation of an Expansion Card ==== |
- | - Unfasten the expansion slot bracket | + | - Unfasten |
- Install the PCIe x16 card into the PCIe x16 slot. | - Install the PCIe x16 card into the PCIe x16 slot. | ||
- | - Secure the bracket.\\ {{: | + | - Secure the graphics card by tightening one screw.\\ {{: |
==== HDD/SSD and USB Installation ==== | ==== HDD/SSD and USB Installation ==== | ||
- | - Turn your XH110G upside down, then unscrew | + | - Turn your XH110G upside down, then unscrew |
- | - Mount the HDD/ | + | - Mount the HDD/ |
- | - Tear off the adhesive tape of the HDD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with an HDD cable. Insert | + | - Tear off the adhesive tape of the HDD/SSD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with the afore mentioned |
- | - Replace the HDD/SSD cover and turn your XH110G upside down.\\ {{: | + | - Replace the HDD/SSD cover and also tighten the screw. Now turn your XH110G upside down again.\\ {{: |
- | - Replace the cover and refasten the thumbscrews.\\ {{: | + | - Replace the cover and refasten the two thumbscrews.\\ {{: |
- Complete. | - Complete. | ||
<WRAP important 60%> | <WRAP important 60%> | ||
- | Please press the " | + | Please press the " |
</ | </ | ||
- | ==== Installation of VESA Mount ==== | + | ==== Installation of a VESA Mount ==== |
<WRAP info 60%> | <WRAP info 60%> | ||
- | Supports | + | The XH110G supports the 75x75 mm and 100x100 mm VESA standard. Installation happens as per illustrations below. |
</ | </ | ||
{{: | {{: | ||
+ | |||
+ | ===== Jumper settings and pinout ===== | ||
+ | ==== RTC battery cable connector ==== | ||
+ | < | ||
+ | 1=BATPWR | ||
+ | 2=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | BAT1 | ||
+ | # | ||
+ | | ||
+ | || 1 2 || | ||
+ | || ■ ■ || | ||
+ | | ||
+ | # | ||
+ | | | ||
+ | v | ||
+ | </ | ||
+ | ==== AC back auto power on ==== | ||
+ | < | ||
+ | 1=OP(+) | ||
+ | 2=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | Open (enabled) | ||
+ | | ||
+ | | ● | 1 |[x]| 1 | ||
+ | | ||
+ | | ■ | 2 | | 2 | ||
+ | | ||
+ | JP1 JP1 | ||
+ | [x]: {" | ||
+ | </ | ||
+ | ==== USB connector ==== | ||
+ | < | ||
+ | 1=GND | ||
+ | 2=USB2_D+ | ||
+ | 3=USB2_D- | ||
+ | 4=+5VS | ||
+ | </ | ||
+ | <a2s> | ||
+ | USB4 | ||
+ | # | ||
+ | | ||
+ | || ■ ■ ■ ■ || | ||
+ | || 4 3 2 1 || | ||
+ | | ||
+ | # | ||
+ | </ | ||
+ | ==== Power button & LED daughterboard connector ==== | ||
+ | < | ||
+ | 1=SATA_LED_+3.3V | ||
+ | 2=SYS_LED_+3.3V | ||
+ | 3=SATA_LED | ||
+ | 4=GND | ||
+ | 5=RST_nBTN | ||
+ | 6=PWRSW- | ||
+ | 7=GND | ||
+ | 8=GND | ||
+ | 9=N/C | ||
+ | 10=N/A | ||
+ | </ | ||
+ | <a2s> | ||
+ | | ||
+ | | ||
+ | | ● | ● | ● | ● | | | ||
+ | SW2 .---.---.---.---.---. | ||
+ | | ■ | ● | ● | ● | ● | | ||
+ | | ||
+ | | ||
+ | </ | ||
+ | ==== Debug port ==== | ||
+ | < | ||
+ | 1=CLK_DBG_24M | ||
+ | 2=LAD1 | ||
+ | 3=SIORST- | ||
+ | 4=LAD0 | ||
+ | 5=LFRAME- | ||
+ | 6=+3.3V | ||
+ | 7=LAD3 | ||
+ | 8=GND | ||
+ | 9=LAD2 | ||
+ | 10=N/A | ||
+ | </ | ||
+ | <a2s> | ||
+ | DBG1 | ||
+ | | ||
+ | 1 | ■ | ● | 2 | ||
+ | | ||
+ | 3 | ● | ● | 4 | ||
+ | | ||
+ | 5 | ● | ● | 6 | ||
+ | | ||
+ | 7 | ● | ● | 8 | ||
+ | | ||
+ | 9 | ● | | 10 | ||
+ | | ||
+ | </ | ||
+ | ==== Fan connector ==== | ||
+ | < | ||
+ | 1=GND | ||
+ | 2=+12V | ||
+ | 3=FAN_TAC | ||
+ | 4=FAN_CTL | ||
+ | </ | ||
+ | <a2s> | ||
+ | FAN1 | ||
+ | # | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | # | ||
+ | </ | ||
+ | ==== Audio & USB daughterboard connector ==== | ||
+ | < | ||
+ | 1=MIC_L | ||
+ | 2=GND | ||
+ | 3=MIC_R | ||
+ | 4=FP_AUDIO-JD | ||
+ | 5=HP_R | ||
+ | 6=MIC-JD | ||
+ | 7=SENSE_B | ||
+ | 8=N/A | ||
+ | 9=HP_L | ||
+ | 10=HP-JD | ||
+ | </ | ||
+ | <a2s> | ||
+ | | ||
+ | | ||
+ | 10 | ● | ● | 9 | ||
+ | | ||
+ | 8 | | ● | 7 | ||
+ | | ||
+ | 6 | ● | ● | 5 | ||
+ | | ||
+ | 4 | ● | ● | 3 | ||
+ | | ||
+ | 2 | ● | ■ | 1 | ||
+ | | ||
+ | </ | ||
+ | ==== Audio & USB daughterboard connector ==== | ||
+ | < | ||
+ | 1=+5VS | ||
+ | 2=+5VS | ||
+ | 3=USB2_D- | ||
+ | 4=USB2_D- | ||
+ | 5=USB2_D+ | ||
+ | 6=USB2_D+ | ||
+ | 7=GND | ||
+ | 8=GND | ||
+ | 9=N/A | ||
+ | 10=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | 2 | ||
+ | .---.---.---.---.---. | ||
+ | | ● | ● | ● | ● | ● | | ||
+ | USB1 .---.---.---.---.---. | ||
+ | | ■ | ● | ● | ● | | | ||
+ | .---.---.---.---.---. | ||
+ | 1 | ||
+ | </ | ||
+ | ==== 2.5” SATA cable connector ==== | ||
+ | < | ||
+ | 1=N/C | ||
+ | 2=N/C | ||
+ | 3=N/C | ||
+ | 4=N/C | ||
+ | 5=GND | ||
+ | 6=GND | ||
+ | 7=GND | ||
+ | 8=+5V | ||
+ | 9=+5V | ||
+ | 10=+5V | ||
+ | 11=+5V | ||
+ | 12=GND | ||
+ | 13=GND | ||
+ | 14=GND | ||
+ | 15=SATA_TX+ | ||
+ | 16=SATA_TX- | ||
+ | 17=GND | ||
+ | 18=SATA_RX- | ||
+ | 19=SATA_RX+ | ||
+ | 20=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | # | ||
+ | | #-#|| | ||
+ | | | ||| | ||
+ | -> |---||| 1 | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | | ||| | ||
+ | | #-#|| | ||
+ | # | ||
+ | SATA1 | ||
+ | </ | ||
+ | ==== Audio & USB daughterboard connector ==== | ||
+ | < | ||
+ | 1=GND | ||
+ | 2=GND | ||
+ | 3=USB2_D+ | ||
+ | 4=USB2_D- | ||
+ | 5=GND | ||
+ | 6=GND | ||
+ | 7=USB3_TX+ | ||
+ | 8=USB3_TX- | ||
+ | 9=GND | ||
+ | 10=GND | ||
+ | 11=USB3_RX+ | ||
+ | 12=USB3_RX- | ||
+ | 13=+5VS | ||
+ | 14=+5VS | ||
+ | 15=+5VS | ||
+ | 16=+5VS | ||
+ | 17=USB2_D+ | ||
+ | 18=USB2_D- | ||
+ | 19=GND | ||
+ | 20=GND | ||
+ | 21=USB3_TX+ | ||
+ | 22=USB3_TX- | ||
+ | 23=GND | ||
+ | 24=GND | ||
+ | 25=USB3_RX+ | ||
+ | 26=USB3_RX- | ||
+ | 27=GND | ||
+ | 28=GND | ||
+ | 29=GND | ||
+ | 30=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | 30 1 | ||
+ | | ||
+ | ################## | ||
+ | # | ||
+ | | ||
+ | </ | ||
==== Related links ==== | ==== Related links ==== | ||
{{backlinks> | {{backlinks> |