Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
faq:xpc_slim:xh110g [2019/07/04 15:02] – [CPU/M.2 Card and ICE Module Installation] christian | faq:xpc_slim:xh110g [2021/09/02 13:29] (current) – TS | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== XH110G ====== | ====== XH110G ====== | ||
- | ===== What' | + | {{page> |
+ | |||
+ | ===== What is the maximum permitted size an internal USB device may have? ===== | ||
The maximum permitted size is 11.5 x 28 x 88 mm. | The maximum permitted size is 11.5 x 28 x 88 mm. | ||
===== What are the maximum dimensions a PCIe card may have? ===== | ===== What are the maximum dimensions a PCIe card may have? ===== | ||
Line 6: | Line 8: | ||
===== Quick Installation Guide ===== | ===== Quick Installation Guide ===== | ||
- | ==== Begin Installation | + | ==== Begin Installation ==== |
- Unscrew the two thumbscrews of the chassis cover.\\ {{: | - Unscrew the two thumbscrews of the chassis cover.\\ {{: | ||
- Slide the cover backwards and upwards.\\ {{: | - Slide the cover backwards and upwards.\\ {{: | ||
Line 25: | Line 27: | ||
Please do not apply excess amount of thermal paste. | Please do not apply excess amount of thermal paste. | ||
</ | </ | ||
- | - As shown in the illustration.\\ {{: | + | - Please look at the illustration |
- Install the M.2 card into the M.2 slot and secure with the screw.\\ {{: | - Install the M.2 card into the M.2 slot and secure with the screw.\\ {{: | ||
- Screw the ICE module on to the mainboard.\\ {{: | - Screw the ICE module on to the mainboard.\\ {{: | ||
Line 32: | Line 34: | ||
This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules. | This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules. | ||
</ | </ | ||
- | - Locate the SO-DIMM | + | - Locate the two SO-DIMM |
- | - Align the notch of the memory module with the one of the memory slot.\\ {{: | + | - Align the notch of the memory module with the one of the relevant |
- Gently insert the module into the slot in a 45-degree angle. | - Gently insert the module into the slot in a 45-degree angle. | ||
- Carefully push down the memory module until it snaps into the locking mechanism.\\ {{: | - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{: | ||
- | - Repeat the above steps to install additional memory | + | - Repeat the above steps to install |
- | ==== Installation of Expansion Card ==== | + | ==== Installation of an Expansion Card ==== |
- | - Unfasten the expansion slot bracket | + | - Unfasten |
- Install the PCIe x16 card into the PCIe x16 slot. | - Install the PCIe x16 card into the PCIe x16 slot. | ||
- | - Secure the bracket.\\ {{: | + | - Secure the graphics card by tightening one screw.\\ {{: |
==== HDD/SSD and USB Installation ==== | ==== HDD/SSD and USB Installation ==== | ||
- | - Turn your XH110G upside down, then unscrew | + | - Turn your XH110G upside down, then unscrew |
- | - Mount the HDD/ | + | - Mount the HDD/ |
- | - Tear off the adhesive tape of the HDD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with an HDD cable. Insert | + | - Tear off the adhesive tape of the HDD/SSD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with the afore mentioned |
- | - Replace the HDD/SSD cover and turn your XH110G upside down.\\ {{: | + | - Replace the HDD/SSD cover and also tighten the screw. Now turn your XH110G upside down again.\\ {{: |
- | - Replace the cover and refasten the thumbscrews.\\ {{: | + | - Replace the cover and refasten the two thumbscrews.\\ {{: |
- Complete. | - Complete. | ||
<WRAP important 60%> | <WRAP important 60%> | ||
- | Please press the " | + | Please press the " |
</ | </ | ||
- | ==== Installation of VESA Mount ==== | + | ==== Installation of a VESA Mount ==== |
<WRAP info 60%> | <WRAP info 60%> | ||
- | Supports | + | The XH110G supports the 75x75 mm and 100x100 mm VESA standard. Installation happens as per illustrations below. |
</ | </ | ||
{{: | {{: | ||
+ | |||
+ | ===== Jumper settings and pinout ===== | ||
+ | ==== RTC battery cable connector ==== | ||
+ | < | ||
+ | 1=BATPWR | ||
+ | 2=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | BAT1 | ||
+ | # | ||
+ | | ||
+ | || 1 2 || | ||
+ | || ■ ■ || | ||
+ | | ||
+ | # | ||
+ | | | ||
+ | v | ||
+ | </ | ||
+ | ==== AC back auto power on ==== | ||
+ | < | ||
+ | 1=OP(+) | ||
+ | 2=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | Open (enabled) | ||
+ | | ||
+ | | ● | 1 |[x]| 1 | ||
+ | | ||
+ | | ■ | 2 | | 2 | ||
+ | | ||
+ | JP1 JP1 | ||
+ | [x]: {" | ||
+ | </ | ||
+ | ==== USB connector ==== | ||
+ | < | ||
+ | 1=GND | ||
+ | 2=USB2_D+ | ||
+ | 3=USB2_D- | ||
+ | 4=+5VS | ||
+ | </ | ||
+ | <a2s> | ||
+ | USB4 | ||
+ | # | ||
+ | | ||
+ | || ■ ■ ■ ■ || | ||
+ | || 4 3 2 1 || | ||
+ | | ||
+ | # | ||
+ | </ | ||
+ | ==== Power button & LED daughterboard connector ==== | ||
+ | < | ||
+ | 1=SATA_LED_+3.3V | ||
+ | 2=SYS_LED_+3.3V | ||
+ | 3=SATA_LED | ||
+ | 4=GND | ||
+ | 5=RST_nBTN | ||
+ | 6=PWRSW- | ||
+ | 7=GND | ||
+ | 8=GND | ||
+ | 9=N/C | ||
+ | 10=N/A | ||
+ | </ | ||
+ | <a2s> | ||
+ | | ||
+ | | ||
+ | | ● | ● | ● | ● | | | ||
+ | SW2 .---.---.---.---.---. | ||
+ | | ■ | ● | ● | ● | ● | | ||
+ | | ||
+ | | ||
+ | </ | ||
+ | ==== Debug port ==== | ||
+ | < | ||
+ | 1=CLK_DBG_24M | ||
+ | 2=LAD1 | ||
+ | 3=SIORST- | ||
+ | 4=LAD0 | ||
+ | 5=LFRAME- | ||
+ | 6=+3.3V | ||
+ | 7=LAD3 | ||
+ | 8=GND | ||
+ | 9=LAD2 | ||
+ | 10=N/A | ||
+ | </ | ||
+ | <a2s> | ||
+ | DBG1 | ||
+ | | ||
+ | 1 | ■ | ● | 2 | ||
+ | | ||
+ | 3 | ● | ● | 4 | ||
+ | | ||
+ | 5 | ● | ● | 6 | ||
+ | | ||
+ | 7 | ● | ● | 8 | ||
+ | | ||
+ | 9 | ● | | 10 | ||
+ | | ||
+ | </ | ||
+ | ==== Fan connector ==== | ||
+ | < | ||
+ | 1=GND | ||
+ | 2=+12V | ||
+ | 3=FAN_TAC | ||
+ | 4=FAN_CTL | ||
+ | </ | ||
+ | <a2s> | ||
+ | FAN1 | ||
+ | # | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | # | ||
+ | </ | ||
+ | ==== Audio & USB daughterboard connector ==== | ||
+ | < | ||
+ | 1=MIC_L | ||
+ | 2=GND | ||
+ | 3=MIC_R | ||
+ | 4=FP_AUDIO-JD | ||
+ | 5=HP_R | ||
+ | 6=MIC-JD | ||
+ | 7=SENSE_B | ||
+ | 8=N/A | ||
+ | 9=HP_L | ||
+ | 10=HP-JD | ||
+ | </ | ||
+ | <a2s> | ||
+ | | ||
+ | | ||
+ | 10 | ● | ● | 9 | ||
+ | | ||
+ | 8 | | ● | 7 | ||
+ | | ||
+ | 6 | ● | ● | 5 | ||
+ | | ||
+ | 4 | ● | ● | 3 | ||
+ | | ||
+ | 2 | ● | ■ | 1 | ||
+ | | ||
+ | </ | ||
+ | ==== Audio & USB daughterboard connector ==== | ||
+ | < | ||
+ | 1=+5VS | ||
+ | 2=+5VS | ||
+ | 3=USB2_D- | ||
+ | 4=USB2_D- | ||
+ | 5=USB2_D+ | ||
+ | 6=USB2_D+ | ||
+ | 7=GND | ||
+ | 8=GND | ||
+ | 9=N/A | ||
+ | 10=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | 2 | ||
+ | .---.---.---.---.---. | ||
+ | | ● | ● | ● | ● | ● | | ||
+ | USB1 .---.---.---.---.---. | ||
+ | | ■ | ● | ● | ● | | | ||
+ | .---.---.---.---.---. | ||
+ | 1 | ||
+ | </ | ||
+ | ==== 2.5” SATA cable connector ==== | ||
+ | < | ||
+ | 1=N/C | ||
+ | 2=N/C | ||
+ | 3=N/C | ||
+ | 4=N/C | ||
+ | 5=GND | ||
+ | 6=GND | ||
+ | 7=GND | ||
+ | 8=+5V | ||
+ | 9=+5V | ||
+ | 10=+5V | ||
+ | 11=+5V | ||
+ | 12=GND | ||
+ | 13=GND | ||
+ | 14=GND | ||
+ | 15=SATA_TX+ | ||
+ | 16=SATA_TX- | ||
+ | 17=GND | ||
+ | 18=SATA_RX- | ||
+ | 19=SATA_RX+ | ||
+ | 20=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | # | ||
+ | | #-#|| | ||
+ | | | ||| | ||
+ | -> |---||| 1 | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | | ||| | ||
+ | | #-#|| | ||
+ | # | ||
+ | SATA1 | ||
+ | </ | ||
+ | ==== Audio & USB daughterboard connector ==== | ||
+ | < | ||
+ | 1=GND | ||
+ | 2=GND | ||
+ | 3=USB2_D+ | ||
+ | 4=USB2_D- | ||
+ | 5=GND | ||
+ | 6=GND | ||
+ | 7=USB3_TX+ | ||
+ | 8=USB3_TX- | ||
+ | 9=GND | ||
+ | 10=GND | ||
+ | 11=USB3_RX+ | ||
+ | 12=USB3_RX- | ||
+ | 13=+5VS | ||
+ | 14=+5VS | ||
+ | 15=+5VS | ||
+ | 16=+5VS | ||
+ | 17=USB2_D+ | ||
+ | 18=USB2_D- | ||
+ | 19=GND | ||
+ | 20=GND | ||
+ | 21=USB3_TX+ | ||
+ | 22=USB3_TX- | ||
+ | 23=GND | ||
+ | 24=GND | ||
+ | 25=USB3_RX+ | ||
+ | 26=USB3_RX- | ||
+ | 27=GND | ||
+ | 28=GND | ||
+ | 29=GND | ||
+ | 30=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | 30 1 | ||
+ | | ||
+ | ################## | ||
+ | # | ||
+ | | ||
+ | </ | ||
==== Related links ==== | ==== Related links ==== | ||
{{backlinks> | {{backlinks> |