Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
faq:xpc_slim:xh110g [2019/07/04 15:05] – [Memory Module Installation] christianfaq:xpc_slim:xh110g [2021/09/02 13:29] (current) TS
Line 1: Line 1:
 ====== XH110G ====== ====== XH110G ======
-===== What'the maximum permitted size an internal USB device may have? =====+{{page>faq:hardware:graphics#litre_format_w_pcie_slot&firstseconly&nofooter&noeditbutton&noreadmore}} 
 + 
 +===== What is the maximum permitted size an internal USB device may have? =====
 The maximum permitted size is 11.5 x 28 x 88 mm. The maximum permitted size is 11.5 x 28 x 88 mm.
 ===== What are the maximum dimensions a PCIe card may have? ===== ===== What are the maximum dimensions a PCIe card may have? =====
Line 6: Line 8:
  
 ===== Quick Installation Guide ===== ===== Quick Installation Guide =====
-==== Begin Installation =====+==== Begin Installation ====
   - Unscrew the two thumbscrews of the chassis cover.\\ {{:faq:xpc_slim:xh110:xh110g:installation01.png?nolink&400|}}   - Unscrew the two thumbscrews of the chassis cover.\\ {{:faq:xpc_slim:xh110:xh110g:installation01.png?nolink&400|}}
   - Slide the cover backwards and upwards.\\ {{:faq:xpc_slim:xh110:xh110g:installation02.png?nolink&400|}}   - Slide the cover backwards and upwards.\\ {{:faq:xpc_slim:xh110:xh110g:installation02.png?nolink&400|}}
Line 37: Line 39:
   - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:faq:xpc_slim:xh110:xh110g:installation12.png?nolink&300|}} {{:faq:xpc_slim:xh110:xh110g:installation13.png?nolink&300|}}   - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:faq:xpc_slim:xh110:xh110g:installation12.png?nolink&300|}} {{:faq:xpc_slim:xh110:xh110g:installation13.png?nolink&300|}}
   - Repeat the above steps to install an additional memory module, if desired.   - Repeat the above steps to install an additional memory module, if desired.
-==== Installation of Expansion Card ==== +==== Installation of an Expansion Card ==== 
-  - Unfasten the expansion slot bracket screws. Remove the back panel bracket and put it aside.\\ \\ <WRAP important 60%>The maximum permitted size for display cards is 208.5 mm x 120 mm x 30 mm. </WRAP>\\ {{:faq:xpc_slim:xh110:xh110g:installation14.png?nolink&500|}}+  - Unfasten the screws of the expansion slot bracket. Remove the bracket and put it aside.\\ \\ <WRAP important 60%>The maximum permitted size for display cards is 208.5 mm x 120 mm x 30 mm. </WRAP>\\ {{:faq:xpc_slim:xh110:xh110g:installation14.png?nolink&500|}}
   - Install the PCIe x16 card into the PCIe x16 slot.   - Install the PCIe x16 card into the PCIe x16 slot.
-  - Secure the bracket.\\ {{:faq:xpc_slim:xh110:xh110g:installation15.png?nolink&400|}}+  - Secure the graphics card by tightening one screw.\\ {{:faq:xpc_slim:xh110:xh110g:installation15.png?nolink&400|}}
 ==== HDD/SSD and USB Installation ==== ==== HDD/SSD and USB Installation ====
-  - Turn your XH110G upside down, then unscrew one screw of the HDD/SSD cover and remove it.\\ {{:faq:xpc_slim:xh110:xh110g:installation16.png?nolink&500|}} +  - Turn your XH110G upside down, then unscrew the screw of the HDD/SSD cover and remove it.\\ {{:faq:xpc_slim:xh110:xh110g:installation16.png?nolink&500|}} 
-  - Mount the HDD/SSD into the bracket with four screws.\\ {{:faq:xpc_slim:xh110:xh110g:installation17.png?nolink&500|}} +  - Mount the HDD/SSD on the bracket with four screws.\\ {{:faq:xpc_slim:xh110:xh110g:installation17.png?nolink&500|}} 
-  - Tear off the adhesive tape of the HDD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with an HDD cable. Insert the USB drive, if required.\\ \\ <WRAP important 60%>The maximum permitted size for an internal USB device is 11.5 mm x 28 mm x 88 mm.</WRAP>\\ {{:faq:xpc_slim:xh110:xh110g:installation18.png?nolink&500|}} +  - Tear off the adhesive tape of the HDD/SSD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with the afore mentioned cable. Insert USB drive, if desired.\\ \\ <WRAP important 60%>The maximum permitted size of an internal USB device is 11.5 mm x 28 mm x 88 mm.</WRAP>\\ {{:faq:xpc_slim:xh110:xh110g:installation18.png?nolink&500|}} 
-  - Replace the HDD/SSD cover and turn your XH110G upside down.\\ {{:faq:xpc_slim:xh110:xh110g:installation19.png?nolink&400|}} +  - Replace the HDD/SSD cover and also tighten the screw. Now turn your XH110G upside down again.\\ {{:faq:xpc_slim:xh110:xh110g:installation19.png?nolink&400|}} 
-  - Replace the cover and refasten the thumbscrews.\\ {{:faq:xpc_slim:xh110:xh110g:installation20.png?nolink&400|}}+  - Replace the cover and refasten the two thumbscrews.\\ {{:faq:xpc_slim:xh110:xh110g:installation20.png?nolink&400|}}
   - Complete.   - Complete.
 <WRAP important 60%> <WRAP important 60%>
-Please press the "Del" key while booting to enter BIOS. Here, please load the optimized BIOS settings.+Please press the "Del" key while booting to enter BIOS. Here, please load the optimised BIOS settings.
 </WRAP> </WRAP>
-==== Installation of VESA Mount ====+==== Installation of VESA Mount ====
 <WRAP info 60%> <WRAP info 60%>
-Supports 75x75 mm and 100x100 mm VESA standard.+The XH110G supports the 75x75 mm and 100x100 mm VESA standard. Installation happens as per illustrations below.
 </WRAP> </WRAP>
 {{:faq:xpc_slim:xh110:xh110g:installation21.png?nolink&500|}} {{:faq:xpc_slim:xh110:xh110g:installation21.png?nolink&500|}}
 +
 +===== Jumper settings and pinout =====
 +==== RTC battery cable connector ====
 +<code>
 +1=BATPWR
 +2=GND
 +</code>
 +<a2s>
 +    BAT1
 + #-------# 
 + |#  -#|
 + || 1 2 ||
 + || ■ ■ ||
 + |#-----#|
 + #-------#
 +   |
 +   v
 +</a2s>
 +==== AC back auto power on ====
 +<code>
 +1=OP(+)
 +2=GND
 +</code>
 +<a2s>
 + Open (enabled)  Short (disabled)
 +     .---.            #---#
 +     | ● | 1          |[x]| 1
 +     .---.            |   |
 +     | ■ | 2          |   | 2
 +     .---.            #---#
 +      JP1              JP1
 +[x]: {"stroke-width":4, "fill":"#999999", "a2s:delref":true}
 +</a2s>
 +==== USB connector ====
 +<code>
 +1=GND
 +2=USB2_D+
 +3=USB2_D-
 +4=+5VS
 +</code>
 +<a2s>
 +     USB4
 + #-----------# 
 + |#---------#|
 + || ■ ■ ■ ■ ||
 + || 4 3 2 1 ||
 + |#      -#|
 + #-----------#
 +</a2s>
 +==== Power button & LED daughterboard connector ====
 +<code>
 +1=SATA_LED_+3.3V
 +2=SYS_LED_+3.3V
 +3=SATA_LED
 +4=GND
 +5=RST_nBTN
 +6=PWRSW-
 +7=GND
 +8=GND
 +9=N/C
 +10=N/A
 +</code>
 +<a2s>
 +               10
 +     .---.---.---.---.---.
 +     | ● | ● | ● | ● |   |
 + SW2 .---.---.---.---.---.
 +     | ■ | ● | ● | ● | ● |
 +     .---.---.---.---.---.
 +               9
 +</a2s>
 +==== Debug port ====
 +<code>
 +1=CLK_DBG_24M
 +2=LAD1
 +3=SIORST-
 +4=LAD0
 +5=LFRAME-
 +6=+3.3V
 +7=LAD3
 +8=GND
 +9=LAD2
 +10=N/A
 +</code>
 +<a2s>
 +        DBG1  
 +     .---.---.
 +   1 | ■ | ● | 2
 +     .---.---.
 +   3 | ● | ● | 4
 +     .---.---.
 +   5 | ● | ● | 6
 +     .---.---.
 +   7 | ● | ● | 8
 +     .---.---.
 +   9 | ● |   | 10
 +     .---.---.
 +</a2s>
 +==== Fan connector ====
 +<code>
 +1=GND
 +2=+12V
 +3=FAN_TAC
 +4=FAN_CTL
 +</code>
 +<a2s>
 +    FAN1
 + #------# 
 +   ■  | 4
 +   ■ || 3
 +   ■ || 2
 +   ■ || 1
 + #------#
 +</a2s>
 +==== Audio & USB daughterboard connector ====
 +<code>
 +1=MIC_L
 +2=GND
 +3=MIC_R
 +4=FP_AUDIO-JD
 +5=HP_R
 +6=MIC-JD
 +7=SENSE_B
 +8=N/A
 +9=HP_L
 +10=HP-JD
 +</code>
 +<a2s>
 +       AUDIO1 
 +     .---.---.
 +  10 | ● | ● | 9
 +     .---.---.
 +   8 |   | ● | 7
 +     .---.---.
 +   6 | ● | ● | 5
 +     .---.---.
 +   4 | ● | ● | 3
 +     .---.---.
 +   2 | ● | ■ | 1
 +     .---.---.
 +</a2s>
 +==== Audio & USB daughterboard connector ====
 +<code>
 +1=+5VS
 +2=+5VS
 +3=USB2_D-
 +4=USB2_D-
 +5=USB2_D+
 +6=USB2_D+
 +7=GND
 +8=GND
 +9=N/A
 +10=GND
 +</code>
 +<a2s>
 +        2         10
 +      .---.---.---.---.---.
 +      | ● | ● | ● | ● | ● |
 + USB1 .---.---.---.---.---.
 +      | ■ | ● | ● | ● |   |
 +      .---.---.---.---.---.
 +        1         9
 +</a2s>
 +==== 2.5” SATA cable connector ====
 +<code>
 +1=N/C
 +2=N/C
 +3=N/C
 +4=N/C
 +5=GND
 +6=GND
 +7=GND
 +8=+5V
 +9=+5V
 +10=+5V
 +11=+5V
 +12=GND
 +13=GND
 +14=GND
 +15=SATA_TX+
 +16=SATA_TX-
 +17=GND
 +18=SATA_RX-
 +19=SATA_RX+
 +20=GND
 +</code>
 +<a2s>
 +   #-----#
 +   | #-#||
 +   | | |||
 +-> |---||| 1
 +   |---|||
 +   |---|||
 +   |---|||
 +   |---|||
 +   |---|||
 +   |---|||
 +   |---|||
 +   |---|||
 +   |---||| 20
 +   | | |||
 +   | #-#||
 +   #-----#
 +    SATA1
 +</a2s>
 +==== Audio & USB daughterboard connector ====
 +<code>
 +1=GND
 +2=GND
 +3=USB2_D+
 +4=USB2_D-
 +5=GND
 +6=GND
 +7=USB3_TX+
 +8=USB3_TX-
 +9=GND
 +10=GND
 +11=USB3_RX+
 +12=USB3_RX-
 +13=+5VS
 +14=+5VS
 +15=+5VS
 +16=+5VS
 +17=USB2_D+
 +18=USB2_D-
 +19=GND
 +20=GND
 +21=USB3_TX+
 +22=USB3_TX-
 +23=GND
 +24=GND
 +25=USB3_RX+
 +26=USB3_RX-
 +27=GND
 +28=GND
 +29=GND
 +30=GND
 +</code>
 +<a2s>
 +    30              1
 +     ||||||||||||||||
 +    ##################
 +    #----------------#
 +     USB5           ↑
 +</a2s>
 ==== Related links ==== ==== Related links ====
 {{backlinks>.}} {{backlinks>.}}
  • Last modified: 2021/09/02 13:29
  • by TS