Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revisionLast revisionBoth sides next revision | ||
faq:xpc_slim:dl10j [2018/12/07 10:35] – BIOS settings TS | faq:xpc_slim:dl10j [2019/07/24 09:47] – [Begin Installation] christian | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== DL10J ====== | ====== DL10J ====== | ||
{{section> | {{section> | ||
+ | {{section> | ||
===== Which LTE/4G modules are suitable? ===== | ===== Which LTE/4G modules are suitable? ===== | ||
Line 18: | Line 19: | ||
The first COM port is marked on this photo:\\ {{: | The first COM port is marked on this photo:\\ {{: | ||
+ | ===== Quick Installation Guide ===== | ||
+ | ==== Begin Installation ==== | ||
+ | <WRAP important 60%> | ||
+ | For safety reasons, please ensure that the power cord is disconnected before opening the case. | ||
+ | </ | ||
+ | - Unscrew the two screws of the chassis cover.\\ {{: | ||
+ | - Slide the cover backward and upward.\\ {{: | ||
+ | - Unfasten the rack mount screw and remove the drive holder.\\ {{: | ||
+ | |||
+ | ==== Memory Module Installation ==== | ||
+ | <WRAP important 60%> | ||
+ | This mainboard does only support 1.2 V DDR4 SO-DIMM memory modules. | ||
+ | </ | ||
+ | - Locate the SO-DIMM slot on the mainboard. | ||
+ | - Align the notch of the memory module with the one of the relevant memory slot.\\ {{: | ||
+ | - Gently insert the module into the slot in a 45-degree angle.\\ {{: | ||
+ | - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{: | ||
+ | - Repeat the above steps to install an additional memory module, if required.\\ {{: | ||
+ | |||
+ | ==== Component Installation ==== | ||
+ | - Please proceed as shown in the illustration, | ||
+ | - Install the M.2 device into the M.2 slot and secure with the screw.\\ {{: | ||
+ | - Place an HDD or SSD in the rack and secure with the four screws from the sides.\\ {{: | ||
+ | - Connect the Serial ATA and power cable to the HDD or SSD. Slide the rack into the chassis and refasten the screws.\\ {{: | ||
+ | |||
+ | ==== Complete ==== | ||
+ | - Replace the cover and refasten the screws.\\ {{: | ||
+ | - Screw the included antenna on to the appropriate connector at the back panel. Make sure it is aligned vertically or horizontally to achieve the best possible signal reception.\\ {{: | ||
+ | - Complete. | ||
+ | - Please press the '' | ||
+ | |||
+ | ===== Jumper settings and pinout ===== | ||
+ | ==== SATA cable connector (SATA1) ==== | ||
+ | < | ||
+ | 1=NA | ||
+ | 2=NA | ||
+ | 3=NA | ||
+ | 4=NA | ||
+ | 5=GND | ||
+ | 6=GND | ||
+ | 7=GND | ||
+ | 8=+5V | ||
+ | 9=+5V | ||
+ | 10=+5V | ||
+ | 11=+5V | ||
+ | 12=GND | ||
+ | 13=GND | ||
+ | 14=GND | ||
+ | 15=SATA_TX_P | ||
+ | 16=SATA_TX_N | ||
+ | 17=GND | ||
+ | 18=SATA_RX_N | ||
+ | 19=SATA_RX_P | ||
+ | 20=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | # | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | # | ||
+ | | ||
+ | ↑ | ||
+ | </ | ||
+ | |||
+ | ==== AC back auto power on (JP1) ==== | ||
+ | < | ||
+ | 1=OP(+) | ||
+ | 2=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | Open (enabled) | ||
+ | |||
+ | | ||
+ | | ■ | ● | |[x] | | ||
+ | | ||
+ | | ||
+ | [x]: {" | ||
+ | </ | ||
+ | |||
+ | ==== Clear CMOS & power button (SW1) ==== | ||
+ | < | ||
+ | 1=RTCRST | ||
+ | 2=+5V | ||
+ | 3=GND | ||
+ | 4=PWRSW | ||
+ | </ | ||
+ | <a2s> | ||
+ | SW1 | ||
+ | .---.---. | ||
+ | 2 | ● | ● | 4 | ||
+ | .---.---. | ||
+ | 1 | ■ | ● | 3 | ||
+ | .---.---. | ||
+ | </ | ||
+ | |||
+ | ==== Battery connector (CN9) ==== | ||
+ | < | ||
+ | 1=V_BAT | ||
+ | 2=GND | ||
+ | </ | ||
+ | <a2s> | ||
+ | # | ||
+ | | ||
+ | || 2 ■|| | ||
+ | | ||
+ | || 1 ■|| | ||
+ | | ||
+ | # | ||
+ | </ | ||
+ | |||
+ | ==== Debug port (DBG1) ==== | ||
+ | < | ||
+ | 1=LPC_24M | ||
+ | 2=LAD1 | ||
+ | 3=SIORST- | ||
+ | 4=LAD0 | ||
+ | 5=LFRAME- | ||
+ | 6=+3.3V | ||
+ | 7=LAD3 | ||
+ | 8=GND | ||
+ | 9=LAD2 | ||
+ | 10=NULL | ||
+ | </ | ||
+ | <a2s> | ||
+ | DBG1 | ||
+ | | ||
+ | 10 | | ● | 9 | ||
+ | | ||
+ | 8 | ● | ● | 7 | ||
+ | | ||
+ | 6 | ● | ● | 5 | ||
+ | | ||
+ | 4 | ● | ● | 3 | ||
+ | | ||
+ | 1 | ● | ■ | 1 | ||
+ | | ||
+ | </ | ||
+ | |||
+ | ==== COM 1 & COM 2 power switch (JP2) ==== | ||
+ | **COM PORT Pin 9 "Ring Indicator" | ||
+ | |||
+ | Configure COM 1 with the first jumper: | ||
+ | * Short Pin 1-2: Pin 9 = RI (default) | ||
+ | * Short Pin 5-7: Pin 9 = +5V | ||
+ | * Short Pin 7-9: Pin 9 = +12V | ||
+ | |||
+ | Configure COM 2 with the second jumper: | ||
+ | * Short Pin 3-4: Pin 9 = RI (default) | ||
+ | * Short Pin 6-8: Pin 9 = +5V | ||
+ | * Short Pin 8-10: Pin 9 = +12V | ||
+ | < | ||
+ | 1=-XRI1 | ||
+ | 2=COM_-XRI1 | ||
+ | 3=-XRI2 | ||
+ | 4=COM_-XRI2 | ||
+ | 5=+5V | ||
+ | 6=+5V | ||
+ | 7=COM1_PWR | ||
+ | 8=COM2_PWR | ||
+ | 9=+12V | ||
+ | 10=+12V | ||
+ | </ | ||
+ | <a2s> | ||
+ | | ||
+ | | ||
+ | | ● | ● | ● | ● | ● | | ||
+ | | ||
+ | | ■ | ● | ● | ● | ● | | ||
+ | | ||
+ | | ||
+ | </ | ||
+ | |||
+ | ==== COM port (COM 1, COM 2) ==== | ||
+ | < | ||
+ | 1=DCD | ||
+ | 2=RX | ||
+ | 3=TX | ||
+ | 4=DTR | ||
+ | 5=GND | ||
+ | 6=DSR | ||
+ | 7=RTS | ||
+ | 8=CTS | ||
+ | 9=RI | ||
+ | 10=NULL | ||
+ | </ | ||
+ | <a2s> | ||
+ | | ||
+ | | ||
+ | | ● | ● | ● | ● | | | ||
+ | | ||
+ | | ■ | ● | ● | ● | ● | | ||
+ | | ||
+ | | ||
+ | </ | ||
==== Related links ==== | ==== Related links ==== | ||
{{backlinks> | {{backlinks> |