Differences

This shows you the differences between two versions of the page.

--- faq:xpc_slim:ds77u [2019/07/19 14:38] – TS
+++ faq:xpc_slim:ds77u [2019/07/24 09:44] – [Operation Position] christian
@@ Line 14: / Line 14: @@
 </WRAP>
   - Unscrew two screws of the chassis cover.\\ {{:faq:xpc_slim:ds77:installation01.png?nolink&500|}}
-  - Slide the cover forwards and upwards.\\ {{:faq:xpc_slim:ds77:installation02.png?nolink&500|}}
+  - Slide the cover forward and upward.\\ {{:faq:xpc_slim:ds77:installation02.png?nolink&500|}}
 ==== Memory Module Installation ====
@@ Line 28: / Line 28: @@
 ==== Mass Storage Installation ====
 === 2.5" HDD/SSD drive ===
-  - Unscrew the rack from chassis.\\ {{:faq:xpc_slim:ds77:installation05.png?nolink&500|}}
+  - Separate the rack from the chassis by undoing one screw.\\ {{:faq:xpc_slim:ds77:installation05.png?nolink&500|}}
-  - Place the HDD or SSD in the rack and secure with two screws from each side.\\ {{:faq:xpc_slim:ds77:installation06.png?nolink&500|}}
+  - Place the HDD or SSD in the rack and secure with two screws, one on each side.\\ {{:faq:xpc_slim:ds77:installation06.png?nolink&500|}}
-  - Lay the HDD or SSD into its drive bay and push it gently to the right until it clicks into place.\\ {{:faq:xpc_slim:ds77:installation07.png?nolink&500|}}
+  - Place the HDD or SSD in the drive bay and push it gently to the right until it clicks into place.\\ {{:faq:xpc_slim:ds77:installation07.png?nolink&500|}}
-  - Refasten screws.\\ {{:faq:xpc_slim:ds77:installation08.png?nolink&500|}}
+  - Refasten the screws.\\ {{:faq:xpc_slim:ds77:installation08.png?nolink&500|}}
 === M.2 SSD module ===
   - As shown, unfasten the screw first.
@@ Line 43: / Line 43: @@
 </WRAP>
-===== Operation Position =====
+===== Jumper settings and pinout =====
+==== COM Port 1 ====
+{{:faq:xpc_slim:ds77:serial_port.jpg?nolink&300|}}
+^COM1 (RS232)^^^^
+^Pin^Signal Name^Pin^Signal Name^
+|1|DCD|2|RX|
+|3|TX|4|DTR|
+|5|GND|6|DSR|
+|7|RTS|8|CTS|
+|9|RI1-| | |
+^COM1 (RS422)^^^^
+^Pin^Signal Name^Pin^Signal Name^
+|1|TXD-|2|TXD+|
+|3|RXD-|4|RXD+|
+|5|GND|6|-|
+|7|-|8|-|
+|9|-| | |
+^COM1 (RS485)^^^^
+^Pin^Signal Name^Pin^Signal Name^
+|1|Data-|2|Data+|
+|3|-|4|-|
+|5|GND|6|-|
+|7|-8|-| |
+|9|-| | |
+==== COM 1 & COM 2 Power Switch ====
+COM PORT Pin 9 "Ring Indicator" (RI) configuration
+<a2s>
+   4   6   8   10
+      .---.---.---.---.---.
+      | ● | ● | ● | ● | ● |
+ JP1  .---.---.---.---.---.
+      | ■ | ● | ● | ● | ● |
+      .---.---.---.---.---.
+   3   5   7   9
+</a2s>
+^JP1^^^^
+^COM1 (pin 9)^^COM2 (pin 9)^^
+^Short Pin^Function^Short Pin^Function^
+|1-2 (Default)|RI1|3-4 (Default)|RI2|
+|5-7|+5V|6-8|+5V|
+|7-9|+12V|8-10|+12V|
+==== AC Back Auto Power ON ====
+^JP9^^
+^Pin^AC Back auto Power ON function^
+|Short 1-2|Disable (Default)|
+|Open|Enable|
+<a2s>
+ Open (enabled)  Short (disabled)
+     .---.            #---#
+     | ● | 2          |[x]| 2
+     .---.            |   |
+     | ■ | 1          |   | 1
+     .---.            #---#
+      JP9              JP9
+[x]: {"stroke-width":4, "fill":"#999999", "a2s:delref":true}
+</a2s>
+==== External Power SW & Clear CMOS ====
+^SW2^^
+^Pin^Signal Name^
+|1|PWRSW|
+|2|+5V|
+|3|GND|
+|4|RTC_RST#|
+<a2s>
+   4
+       .---.---.
+       | ● | ● |
+ SW2   .---.---.
+       | ■ | ● |
+       .---.---.
+   3
+</a2s>
+===== Operating Position =====
 Please make sure to use either the supplied feet or the VESA mount.
 ==== Related links ====
 {{backlinks>.}}