Differences

This shows you the differences between two versions of the page.

--- faq:xpc_slim:dl10j [2019/01/31 17:20] – Shuttle
+++ faq:xpc_slim:dl10j [2019/07/11 08:36] – TS
@@ Line 18: / Line 18: @@
 ===== Where is COM port #1? =====
 The first COM port is marked on this photo:\\ {{:faq:xpc_slim:dl10j:dl10j_com1.jpg?nolink&400|}}
+===== Quick Installation Guide =====
+==== Begin Installation ====
+<WRAP important 60%>
+For safety reasons, please ensure that the power cord is disconnected before opening the case.
+</WRAP>
+  - Unscrew the two screws of the chassis cover.\\ {{:faq:xpc_slim:dl10j:installation01.png?nolink&500|}}
+  - Slide the cover backwards and upwards.\\ {{:faq:xpc_slim:dl10j:installation02.png?nolink&500|}}
+  - Unfasten the rack mount screw and remove the drive holder.\\ {{:faq:xpc_slim:dl10j:installation03.png?nolink&500|}}
+==== Memory Module Installation ====
+<WRAP important 60%>
+This mainboard does only support 1.2 V DDR4 SO-DIMM memory modules.
+</WRAP>
+  - Locate the SO-DIMM slot on the mainboard.
+  - Align the notch of the memory module with the one of the relevant memory slot.\\ {{:faq:xpc_slim:dl10j:installation04.png?nolink&500|}}
+  - Gently insert the module into the slot in a 45-degree angle.\\ {{:faq:xpc_slim:dl10j:installation05.png?nolink&500|}}\\ {{:faq:xpc_slim:dl10j:installation06.png?nolink&500|}}
+  - Carefully push down the memory module until it snaps into the locking mechanism.\\ {{:faq:xpc_slim:dl10j:installation07.png?nolink&500|}}
+  - Repeat the above steps to install an additional memory module, if required.\\ {{:faq:xpc_slim:dl10j:installation08.png?nolink&500|}}
+==== Component Installation ====
+  - Please proceed as shown in the illustration, and locate the M.2 key slot on the mainboard.\\ {{:faq:xpc_slim:dl10j:installation09.png?nolink&500|}}
+  - Install the M.2 device into the M.2 slot and secure with the screw.\\ {{:faq:xpc_slim:dl10j:installation10.png?nolink&500|}}
+  - Place an HDD or SSD in the rack and secure with the four screws from the sides.\\ {{:faq:xpc_slim:dl10j:installation11.png?nolink&500|}}
+  - Connect the Serial ATA and power cable to the HDD or SSD. Slide the rack into the chassis and refasten the screws.\\ {{:faq:xpc_slim:dl10j:installation12.png?nolink&500|}}
+==== Complete ====
+  - Replace the cover and refasten the screws.\\ {{:faq:xpc_slim:dl10j:installation13.png?nolink&500|}}
+  - Screw the included antenna on to the appropriate connector at the back panel. Make sure it is aligned vertically or horizontally to achieve the best possible signal reception.\\ {{:faq:xpc_slim:dl10j:installation14.png?nolink&500|}}
+  - Complete.
+  - Please press the ''Del'' key while booting to enter BIOS. Here, please load the optimised BIOS settings.
+===== Jumper settings and pinout =====
+==== SATA cable connector (SATA1) ====
+<code>
+=NA
+=NA
+=NA
+=NA
+=GND
+=GND
+=GND
+=+5V
+=+5V
+=+5V
+=+5V
+=GND
+=GND
+=GND
+=SATA_TX_P
+=SATA_TX_N
+=GND
+=SATA_RX_N
+=SATA_RX_P
+=GND
+</code>
+<a2s>
+ #---------------------------#
+ |#-------------------------#|
+ ||  |||||||||||||||||||||  ||
+ |#--|||||||||||||||||||||--#|
+ |   |||||||||||||||||||||   |
+ #---------------------------#
+                   20
+     ↑
+</a2s>
+==== AC back auto power on (JP1) ====
+<code>
+=OP(+)
+=GND
+</code>
+<a2s>
+ Open (enabled)  Short (disabled)
+   .---.---.        #------#
+   | ■ | ● |        |[x]   |
+   .---.---.        #------#
+   2            1  2
+[x]: {"stroke-width":4, "fill":"#999999", "a2s:delref":true}
+</a2s>
+==== Clear CMOS & power button (SW1) ====
+<code>
+=RTCRST
+=+5V
+=GND
+=PWRSW
+</code>
+<a2s>
+       SW1
+    .---.---.
+| ● | ● | 4
+    .---.---.
+| ■ | ● | 3
+    .---.---.
+</a2s>
+==== Battery connector (CN9) ====
+<code>
+=V_BAT
+=GND
+</code>
+<a2s>
+ #------#
+ |#----#|
+ || 2 ■||
+ |     ||
+ || 1 ■||
+ |#----#| ->
+ #------#
+</a2s>
 ==== Related links ====
 {{backlinks>.}}